Deep Concave vs. Flat Wheel Centre & Caliper Clearance

Wheels 'N Customs Icon
WHEELS 'N CUSTOMS
TECHNICAL GUIDE: CONCAVE FITMENT & CALIPER CLEARANCE

Concave Wheels Guide: Deep Concave vs. Flat Wheel Centre & Caliper Clearance

Concave wheels are among the absolute favourites in modern car styling. Instead of a flat wheel centre, the spokes curve deeply inward from the outer wheel lip towards the central hub. This creates an aggressive, three-dimensional depth effect that gives the car a wide and muscular look. Brands such as Concaver Wheels, Wheelforce and the Japan Racing (JR-Wheels) series owe a large part of their popularity to these spectacular designs.

Even so, fitting concave wheels often leads to unexpected fitment issues: "Why doesn't a concave wheel fit my car even though the ET value and PCD are correct?" and "What is the X-factor of a wheel with Big Brake Kits?" In this technical guide, the specialists at Wheels 'N Customs explain the direct link between wheel width, Einpresstiefe (ET), spoke curvature and caliper clearance.

1. The Different Concavity Profiles

Manufacturers of high-quality wheels now cast or forge their designs in various profile levels. This makes it possible to visually match the front and rear axles:

Flat / Performance Concave

Minimal spoke curvature. Virtually flat wheel centre. Naturally offers the most inner clearance and is commonly used on the front axle of front-wheel-drive vehicles with limited wheel well space.

Mid Concave

A clearly visible curvature towards the hub. The ideal all-round balance between aesthetic depth and sufficient brake clearance for OEM sport brakes on 8.5J to 9.0J wheels.

Deep Concave

Spectacular depth where the spokes dive far inwards. Usually requires a wheel width of at least 9.5J to 10J and sufficiently low ET values. Very popular on the rear axle of staggered setups.

Extreme Concave

The most extreme angle possible. Achievable only with very wide wheels (10.5J to 12J+) with low or negative ET values. Largely reserved for wide sports coupés or widebody conversions.

2. The Mathematical Triangle: J-Width, ET Value & Depth

Many car owners expect every wheel model, in any desired size, to have the same deep look as in the promo photos. Physically, however, this is impossible. Concavity is the direct mathematical result of two factors:

  • Wheel Width (J value): The wider the wheel (for example 10.5J versus 8.0J), the more physical space there is between the outer lip and the mounting flange to let the spokes slope inward. A narrow wheel of 7.5J or 8.0J will by definition have a relatively flat profile.
  • The ET Value (Offset): A lower ET value (such as ET20 vs. ET45) moves the mounting face deeper towards the inside of the wheel. This allows the wheel centre to be recessed deeper into the wheel, maximising concavity.
  • The Pitfall with High ET Values: Cars that require very high ET values from the factory (such as ET48 to ET54 on front-wheel-drive models like the VW Golf, Ford Focus or Mercedes A-Class) cannot technically fit Deep Concave wheels without the wheels protruding far beyond the wheel arches.

3. What Is a Wheel’s X-Factor with Big Brake Kits?

This is where the biggest misunderstanding in the tuning world arises: "The PCD matches, the centre bore matches and the offset (ET) is identical to OEM, yet the wheel still clamps hard against the brake caliper."

Definition of the X-Factor (Caliper Clearance)

The X-factor is the three-dimensional distance between the mounting face of the wheel hub and the inner side of the wheel spokes at the height of the brake caliper. The ET value only tells you where the centre of the wheel sits relative to the centreline, but says nothing about the curvature or thickness of the spokes.

With concave wheels, the spokes dive diagonally from the rim edge towards the centre. Exactly where a large multi-piston brake caliper (such as Brembo 4-pot or 6-pot calipers on BMW M-Performance, Audi RS, Mercedes-AMG or Brembo Big Brake Upgrades) protrudes outward, the spoke of a concave wheel bends perilously close towards the middle. The result: the rear of the spoke scrapes against the outer edge of the brake caliper.

4. Profile Matrix: Concavity vs. Brake Clearance

Profile Type Common J Sizes X-Factor (Caliper Clearance) Suitability for Big Brakes
Flat / Performance 7.5J to 8.5J Very Large (High X-factor) Fits directly over almost all calipers
Mid Concave 8.5J to 9.5J Average Usually fits; check required for 6-pots
Deep Concave 9.5J to 10.5J Critical / Low Spacers often required on the front axle
Extreme Concave 10.5J to 12J+ Very Limited Almost exclusively rear axle or custom ET

5. Why Concave Wheels Sometimes Require Spacers

When a desired concave wheel touches the brake caliper, installing a high-quality wheel spacer (track widener) is often the only and most effective solution:

  • Creating Spoke Clearance: By installing a spacer of, for example, 5 mm, 10 mm or 12 mm between the hub and the wheel, the entire spoke profile shifts axially outward. The slanted curve of the concave spoke then sits exactly those crucial millimetres clear of the corner of the brake caliper (minimum 3 to 4 mm free clearance per TÜV standards).
  • Reduction of the Effective ET Value: Remember that a spacer reduces the effective ET value (an ET40 wheel with a 10 mm spacer acts as ET30). Always check in advance that the tyre will not rub against the fender edge (fender rub).
  • Test Fitting Without Tyres: Always first test a new concave wheel ‘bare’ (without a mounted tyre) on both the front and rear axle. Rotate the wheel by hand to check that the spokes do not rub against the brake caliper anywhere. As soon as a tyre has been machine-mounted on a wheel, the right of withdrawal lapses in accordance with the terms.

Have Your Concave Wheels Professionally Matched & Fitted

Unsure whether a Deep Concave profile will clear your factory performance brakes or Big Brake Kit? In our specialised workshop in Nijkerk, our technicians precisely measure the brake calliper depth and wheel arch clearance in advance. We fit your complete wheel set scratch-free, including ultra-precise balancing and TPMS sensor programming.

Unsure About the X-Factor for Your Brake Callipers?

Send us your vehicle details and calliper type; our fitment specialists will gladly calculate the exact spoke clearance for you in advance.

 

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl