Purchase point: Wheels 'N Customs (Nijkerk, Netherlands)
Specialism: Eccentric Wobble Bolts & Wobble Nuts (Wobble Bolts)
Application: Bridging up to 2 mm PCD Difference
Service: Directly Available from Stock, Tailored Advice & Workshop Fitting

Do you want to fit a beautiful set of wheels to your car, but the wheel has a small difference in bolt pattern (for example wheels with 5x114.3 on a car with 5x112, or 4x100 wheels on an Alfa/Fiat with 4x98)? With special **wobble bolts** (also called eccentric bolts, spring bolts or sliding bolts) or **wobble nuts** you can bridge a bolt pattern difference of up to 2 mm in a 100% safe and approved way.
Safety & Immediate Supply:
At Wheels 'N Customs you can buy high-quality, hardened wobble bolts and wobble nuts in various thread sizes (M12x1.25, M12x1.5, M14x1.25, M14x1.5). Our wobble bolts are of course TÜV-approved and completely safe for daily road use. Order individual bolts online immediately or combine them with a **complete set of wheels fitted with tyres and TPMS sensors**.
On a normal wheel bolt the conical seat is fixed to the threaded shaft. A wobble bolt, however, has a **separate conical ring** directly beneath the bolt head. This ring has room to shift eccentrically (off-centre) by up to 2 mm.
When you tighten the bolt, the thread finds its way into the thread of the wheel hub (which is slightly off-centre relative to the bolt hole in the wheel). The loose conical ring slides along and clamps the wheel flat against the brake disc over the full 60° conical seat of the bolt hole.
The maximum difference you can bridge with stud bolts or spacer nuts is **a maximum of 2 millimetres** in pitch diameter. Below you will find the most popular applications:
| Wheel Bolt Pattern Vehicle | Wheel Bolt Pattern Wheel | Typical Models / Brands |
|---|---|---|
| 4x98 | 4x100 | Alfa Romeo, Fiat 500, Lancia, Citroën, Ford Ka to standard JDM/Euro 4x100 wheels. |
| 5x98 | 5x100 | Alfa Romeo 147/156/GTV, Fiat to VW Golf 4 / Audi A3 5x100 wheels. |
| 5x110 | 5x112 | Opel, Saab, Alfa Romeo 159/Brera to Audi, VW, Mercedes & BMW G-series wheels. |
| 5x112 | 5x114.3 | Volkswagen, Audi, Mercedes, Seat to Japanese/American JDM & Tesla wheels. |
| 5x114.3 | 5x115 | Toyota, Nissan, Honda, Mazda to Chrysler, Dodge, Chevrolet. |
| 5x108 | 5x110 | Ford, Volvo, Renault to Opel / Saab. |
Because stud bolts rotate eccentrically in the wheel’s bolt hole, **the bolts DO NOT centre the wheel on the axle**. The wheel must therefore be 100% accurately centred on the car’s steel wheel hub.
If the wheel’s hub opening is larger than the car’s wheel hub, you must **ALWAYS** use precise aluminium centre rings. Without correct hub centring an eccentric fitment will occur, causing severe steering vibrations at 100 km/h.
Yes. If stud bolts are made of hardened steel (grade 10.9), have sufficient thread length (at least 6.5 to 8 full turns tightened) and are combined with the correct hub centring, this is 100% approved for the MOT in the Netherlands and Belgium.
Almost all aftermarket alloy wheels (such as Japan Racing, Concaver, Lenso, Borbet) require a 60° conical seat. Therefore almost all stud bolts are manufactured with a conical spacer ring. Original wheels from e.g. VW/Audi sometimes have a ball-conical seat; always check this beforehand.
We offer a very wide range of secure payment options. Pay easily via iDEAL, Bancontact (Belgium), Credit Card, PayPal, SEPA Bank Transfer, Belfius Direct Net, KBC/CBC Payment Button, SOFORT Banking, EPS and instalment options (such as In3 on our payment page).
Our wheel and fitment specialists are happy to calculate the exact bolt pattern deviation, thread and hub diameter for your vehicle in advance. We supply both individual stud bolts and complete wheel sets including mounted tyres.
Request Advice from Our Specialist View Our Webshop