What is ET Value, Bolt Pattern (PCD) and Custom Drilling? | Technical Guide

Technical Wheel Guide: ET Value, PCD and Custom Drilling Explained

Buying aftermarket wheels can feel like advanced maths. Terms like ET value, Offset, Centre Bore, PCD and Custom Drilling are everywhere. What do these figures determine and how do you prevent a new wheel from fouling your brakes or wheel arches? The specialists at Wheels 'N Customs explain the concept step by step, including a handy calculation example!

The quick answer:
The ET value (Offset) determines how far a wheel sits inwards or outwards in the wheel arch. The lower the ET value, the further the wheel sits to the outside. The Bolt Pattern (PCD) indicates the number of bolt holes and the diameter of their circle (e.g. 5x112 means 5 bolts on a 112 mm circle). If the PCD is incorrect, the wheel simply will not fit the hub.

1. What is the ET Value (Offset)?

The abbreviation ET stands for the German word Einpresstiefe (in English: Offset). This value is always expressed in millimetres (mm). The ET value is the distance between the imaginary centreline of the wheel and the mounting face (the part of the wheel that sits flush against the car’s hub).

  • Positive ET value (+): The mounting face sits closer to the outside (road side) of the wheel. The wheel sits deeper into the wheel arch. This is standard for 95% of all modern front-wheel-drive (FWD) vehicles.
  • Zero ET value (0): The mounting face is exactly in the middle of the wheel.
  • Negative ET value (-): The mounting face sits deeper inside the wheel, closer to the brakes. As a result, the wheel sticks out far (beyond the arch). We often see this on lifted 4x4 pick-ups (e.g. ET-44) for a massive, wide look.
Adjustment Effect on Track Width Risk if deviation is too large
Lowering the ET value (e.g. from 45 to 35) Wheel sits further OUT Rubbing against the edge of the wheel arch (fenders).
Raising the ET value (e.g. from 35 to 45) Wheel sits further IN Rubbing against the shock absorber or strut.

2. The Maths: How do you calculate the new wheel position?

When fitting a wider wheel, not only does the ET value affect the fitment, but so does the overall width of the wheel (expressed in inches). Because 1 inch equals exactly 25.4 millimetres, we can accurately calculate the new position of the wheel relative to your wheel arch.

To determine how many millimetres the outer lip of the new wheel will protrude further out compared to the old wheel, we use the following calculation method:

Outer Side Difference (mm) =

[ ( Widthnew - Widthold ) / 2 ] × 25.4 + ( ETold - ETnew )

Step-by-step Example:
Suppose you have an original OEM wheel of 8.0J width with ET45. You want to buy a new wheel of 9.0J width with ET35.

  • Width difference: 9.0 inch - 8.0 inch = 1.0 inch. Half of this width grows outward, so 0.5 inch. This equals 12.7 mm (0.5 x 25.4).
  • ET difference: ET45 - ET35 = +10 mm (a lower ET value pushes the wheel 10 mm further outward).
  • Total increase to the outer edge: 12.7 mm + 10 mm = 22.7 mm.

The outer edge of the new wheel will therefore sit exactly 22.7 mm further outward (towards the wheel arch) than the original wheel!

3. What are PCD and Custom Drilling?

The term PCD (Pitch Circle Diameter), called the bolt pattern, is the diameter of the imaginary circle that can be drawn through the centre of all the wheel bolt holes.

Nowadays, premium brands such as JR Wheels, Concaver and AXE offer so-called 'Blank' wheels. This means the wheel leaves the factory without bolt holes and with a solid, unmachined wheel centre (hub section).

  • The process: As soon as you place an order, the factory loads a computer-controlled CNC milling machine with your specific vehicle data.
  • Custom PCD: The holes are drilled exactly to your car’s bolt pattern (for example exactly 5x114.3 or 5x112).
  • Custom Offset (ET machining): The machine then shaves millimetres of material from the back of the wheel centre until the exact desired ET value is reached (e.g. precisely ET38 for the ultimate flush fitment).

4. Centre Bore and Centring Rings

The large hole in the exact middle of the wheel is called the centre bore. This hole centres the wheel on your car’s hub and carries the weight of the vehicle. Wheel bolts only clamp the wheel to the hub; they do not carry the load!

When do I need centring rings?
If you buy a wheel with a universal large centre bore of, for example, 72.6 mm, and your car’s hub has a diameter of 57.1 mm (standard on e.g. Volkswagen/Seat/Skoda), there is dangerous play between the wheel and the hub. This will inevitably cause severe steering wheel vibration on the motorway. By clicking a centring ring into the wheel, the hole is perfectly filled to exactly 57.1 mm. At Wheels 'N Customs we always include the correct rings free of charge.

5. Frequently Asked Questions (FAQ)

Can I fit a wheel with a lower ET value than the original?

Yes, this is very common in the tuning world. Lowering the ET value makes the wheel sit nicer and wider in the arch (the well-known 'Flush' stance). However, we recommend not deviating more than 10 to 15 mm from the original ET value, unless there is sufficient space in the wheel arch or camber adjustments are made.

What is a wheel’s X-factor?

The X-factor (or Spoke Clearance) is independent of the ET value. It is the bulge or curve of the spokes on the inner side of the wheel. A high X-factor is absolutely necessary if your car is equipped with large performance brakes (Big Brake Kits or Carbon Ceramics). If the X-factor is too small, the spokes will foul the side of the brake calliper, regardless of the ET value.

Are spacers safe to adjust the ET value?

Yes, provided you use quality, hub-centric spacers and correctly extended wheel bolts. A 10 mm spacer lowers your effective ET value by exactly 10 mm. A wheel with ET45 and a 10 mm spacer therefore behaves on the hub exactly like an ET35 wheel.

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl