Wheel Fitment Guide - Abarth 595 & 695 (Competizione / Turismo / Esseesse)

Wheels Fitment Guide - Abarth 595 & 695 (Competizione / Turismo / Esseesse)

Model range 595 & 695 (2012-2024) | 1.4 T-Jet Turbo (145 hp to 180 hp - 250 Nm) | Koni FSD Suspension & Record Monza Exhaust

Wheels Fitment Guide Abarth 595 695 Competizione Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Abarth 595 & 695?
The Abarth 595 and 695 (including iconic variants such as the Turismo, Competizione, Esseesse and Biposto, with an accessible new price between € 28.000,- and € 39.000,-) are the undisputed kings of the Italian pocket rockets. Powered by the characterful 1.4-litre T-Jet turbo engine (available from 145 HP to 180 HP) and a raw Record Monza or Akrapovi? exhaust note, the Abarth delivers maximum driving fun in a compact package. The car uses the specific Fiat bolt pattern 4x98 with a 58.1 mm centre bore and M12x1.25 wheel bolts. Factory-fitted wheels are 16 inch (6.5J ET35) or the much more extreme 17 inch alloy wheels (7.0J ET38 with 205/40 R17 tyres). On the more powerful Competizione and Esseesse models (180 HP) the vehicle is standard equipped with solid 305 mm 4-piston aluminium Brembo brakes at the front, which place high demands on spoke clearance and inner offset of aftermarket wheels. At Wheels 'N Customs in Nijkerk we check every order in advance based on your chosen Make, Model, Version, Year of manufacture and chassis number.

1. Factory specifications (OEM) Abarth 595 & 695

The values below represent the original factory parameters for the Abarth 595 & 695 (Turismo / Competizione / Esseesse). Use these as a technical reference when purchasing new wheels or wheel spacers.

Specification Factory Value (OEM) Notes & Advice
P.C.D. (Pitch Circle Diameter) 4x98 Specific Fiat/Abarth 4-bolt pattern. (4x100 can only be used with eccentric bolts).
Centre Bore (CB) 58.1 mm Standard Fiat/Abarth hub bore. Hub centring rings required for wheels with a larger bore (e.g. 67.1 mm or 73.1 mm).
Wheel Fastener Type M12 x 1.25 Conical Bolts Torque of 100 Nm recommended by Abarth.
OEM Wheel Sizes (16" Base 595) 6.5J x 16 ET35 Factory 16-inch 8-spoke alloy wheels in a square fitment.
OEM Wheel Sizes (17" Turismo / Competizione / Esseesse) 7.0J x 17 ET38 (or ET35) Factory 17-inch Corsa, Formula, Supersport or Esseesse wheels in Matt Black, White or Titanium.
OEM Tyre Sizes 195/45 R16 (on 16") / 205/40 R17 (on 17") Supplied on Michelin Pilot Sport 3 / 4 or Pirelli P Zero Nero GT with XL Load Index.

2. Aftermarket Fitment Guide (17" & 18" Abarth 595/695)

Want to give your Abarth 595 or 695 a tighter fill of the wide wheel arches, a motorsport Esseesse look or weight savings with Flow Formed wheels from brands like JR-Wheels (JR11 / JR30 / SL01), OZ Racing (Formula HLT / Ultraleggera / Superturismo), Japan Racing, Concaver, MSW, Autec, Sparco, Novitec or Maxton-styling? Below are the ideal sizes for a scratch-free fit, also when lowered with Koni FSD, Bilstein, Eibach or KW coilovers.

Wheel Diameter & Construction Position Recommended Wheel Width (J) Ideal ET Range Recommended Tyre Size
17 Inch (OEM+ Flush Street Performance Sweet Spot) Front & Rear (Square) 7.0J / 7.5J ET30 - ET35 205/40 R17 (or 215/40 R17)
17 Inch (Aggressive Trackday / Brembo Clearance Setup) Front & Rear (Square) 7.5J ET25 - ET30 205/40 R17 (Semi-slicks Nankang NS-2R / Cup 2)
18 Inch (Show & Extreme Stance Setup) Front & Rear (Square) 7.5J / 8.0J ET30 - ET35 215/35 R18 (Slight stretch on 8.0J)

3. Wheel Spacers & PCD Adapters for Abarth 595 & 695

Want to push the original 17" Competizione or Esseesse factory wheels (7.0J ET38) a bit further out to sit flush with aggressive bumpers?

  • Wheel Spacers: On the original 7.0J ET38 factory wheels you can fit H&R, Eibach or Athena spacers of 12 mm to 16 mm at the front and 15 mm to 20 mm at the rear. Use only hub-centric aluminium spacers with the specific 4x98 PCD and 58.1 mm hub fitment with extended M12x1.25 wheel bolts.
  • 4x98 vs 4x100 Eccentric Bolts: If you choose an aftermarket wheel with a 4x100 PCD, we carry out the installation in Nijkerk using approved TUV-certified eccentric M12x1.25 sliding bolts to safely compensate the 2 mm discrepancy.

4. Fixed Labour Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we daily fit wheels, exhausts, bodykits and suspensions on 2 to 5 cars. We apply transparent fixed rates (excl. VAT):

Part / Service Labour Rate (Excl. VAT) Indicative Labour Time
Complete Wheel Set Mounting & Balancing € 75 - € 115 45 - 60 minutes
Front Spoiler / Lip / Splitter Fitting € 80 - € 120 45 - 60 minutes
Side Skirts Set Fitting € 103 - € 145 60 - 90 minutes
Rear Diffuser Installation € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Boot Spoiler Installation € 55 - € 80 30 - 45 minutes
Sidebars Set Installation (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Installation (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Tip (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-movers"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical knowledge. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, which gives you 100% fitment guarantee, factory warranty and MOT-certainty.

How does the vehicle inspection and fitment guarantee of Wheels 'N Customs work?

In our webshop you filter parts by Make, Model, Version and Year (we deliberately do not use a licence plate filter to avoid incorrect database links). After placing your order our specialists carry out a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for the inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW/Bilstein, Record Monza/Akrapovi?/Magneti Marelli exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT in the Netherlands and vehicle inspection in Belgium.

What are the conditions for withdrawal and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, customised drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior verification of Make/Model/Version restocking costs of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Abarth 595 or 695 (Competizione / Turismo / Esseesse), would you like advice on 305mm Brembo brake caliper clearance, OZ Racing wheels or spacers, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl