Wheel Fitment Guide - Alfa Romeo Giulietta QV & Veloce (940 1750 TBi 235 / 240 hp)

Wheels Fitment Guide - Alfa Romeo Giulietta Quadrifoglio Verde / Veloce (940)

Model generation Type 940 (2010-2020) | 1750 TBi Turbo (235 hp Manual / 240 hp TCT - 340 Nm) | Alfa DNA Q2 Electronic Differential & Brembo Brakes

Wheels Fitment Guide Alfa Romeo Giulietta QV Veloce Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Alfa Romeo Giulietta QV / Veloce?
\r\nThe Alfa Romeo Giulietta Quadrifoglio Verde (QV, later produced as Giulietta Veloce with the light 4C aluminium engine block, from 2010 to 2020 with an original new price of around € 36.000,- to € 42.000,-) is a stunning Italian hot hatch. Powered by the fiery 1.75-litre TBi turbo engine (235 HP with manual gearbox or 240 HP with TCT dual-clutch gearbox) and equipped with the electronic Q2 limited-slip differential, the Giulietta delivers fantastic performance. The Giulietta (Type 940) uses the bolt pattern 5x110 with a 65.1 mm centre bore and M12x1.25 wheel bolts. From the factory the QV rides on 18 inch 'Telephone number' dial or Turbine alloy wheels (7.5J ET41 with 225/40 R18 tyres). Because the QV and Veloce are standard-fitted with solid red 330 mm 4-piston aluminium Brembo front calipers, they impose specific requirements on spoke clearance and offset when choosing aftermarket wheels. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Trim, Year and chassis number.

The image below shows an original alloy wheel of the Alfa Romeo Giulietta QV with red Brembo brake calipers:

Original alloy wheel of the Alfa Romeo Giulietta QV with red Brembo brake calipers

1. Factory specifications (OEM) Alfa Romeo Giulietta QV / Veloce

The values below represent the original factory parameters of the Alfa Romeo Giulietta Quadrifoglio Verde and Veloce (940). Use these as a technical reference when purchasing new wheels or wheel spacers.

Specification Factory value (OEM) Notes & Advice
Pitch pattern (PCD) 5x110 Specific VAG/GM/Alfa 5-lug bolt circle.
Centre bore (CB) 65.1 mm Standard Alfa Romeo/Opel hub bore. Centre rings required for wheels with a larger hub bore (e.g. 67.1 mm or 73.1 mm).
Wheel fastener type M12 x 1.25 Conical Bolts Tightening torque of 110 Nm recommended by Alfa Romeo.
OEM Wheel sizes (18" Standard QV Dial / Turbine) 7.5J x 18 ET41 Factory 18 inch alloy wheels in Anthracite, Silver or Gloss Black in a square setup.
OEM Tyre sizes 225/40 R18 Supplied on Pirelli P Zero, Michelin Pilot Sport 4 or Continental SportContact with XL Load Index.

2. Aftermarket Fitment Guide (18" & 19" Giulietta QV)

Want to fit your Alfa Romeo Giulietta QV with a wider track, a more aggressive stance or save weight using Flow Formed wheels from brands like JR-Wheels (JR11 / JR21 / JR30 / SL01), OZ Racing (Formula HLT / Ultraleggera / Superturismo LM), Japan Racing, Concaver, MSW, Autec, Sparco, Ragazzon or Maxton-styling? Below are the ideal sizes for a scratch-free fit, also when lowered with Eibach, H&R, Novitec or KW coilovers.

Wheel diameter & construction Position Recommended wheel width (J) Ideal ET range Recommended tyre size
18 Inch (OEM+ Flush Street Performance Sweet Spot) Front & Rear (Square) 8.0J ET32 - ET38 225/40 R18 (or 235/40 R18)
19 Inch (OEM+ Flush Show & Performance Stance) Front & Rear (Square) 8.0J / 8.5J ET33 - ET38 225/35 R19 (or 235/35 R19)
19 Inch (Aggressive Deep Concave Setup) Front & Rear (Square) 8.5J ET30 - ET35 225/35 R19 (Light stretch on 8.5J)

3. Wheel spacers & fitting guidelines for Giulietta QV

Want to push the original 18" QV factory wheels (7.5J ET41) slightly further out to sit flush with the body arches?

  • Wheel spacers: On the original 7.5J ET41 factory wheels, H&R, Eibach or Novitec spacers of 12 mm to 15 mm can be fitted at the front and 15 mm to 18 mm at the rear. Use only hub-centric aluminium spacers with the specific 5x110 bolt pattern and 65.1 mm hub fitment with extended M12x1.25 wheel bolts.
  • Brembo caliper clearance: Because the Giulietta QV/Veloce is fitted up front with large 330 mm 4-pot Brembo calipers, always check with aftermarket wheels that the spokes do not contact the side of the brake caliper.

4. Fixed workshop labour rates Nijkerk

In our spacious and professional workshop in Nijkerk we fit wheels, exhausts, bodykits and suspension to 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):

Part / Operation Labour rate (Excl. VAT) Indicative fitting time
Complete wheel set mounting & balancing € 75 - € 115 45 - 60 minutes
Front spoiler / bumper lip / splitter fitting € 80 - € 120 45 - 60 minutes
Side skirts set fitting € 103 - € 145 60 - 90 minutes
Rear diffuser fitting € 95 - € 145 45 - 75 minutes
Roof spoiler extension / boot spoiler fitting € 55 - € 80 30 - 45 minutes
Sidebars set fitting (Commercial vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars fitting (Commercial vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust outlet (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-movers"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, giving you 100% fitment guarantee, manufacturer warranty and MOT certainty.

How does Wheels 'N Customs' vehicle inspection and fitment guarantee work?

In our webshop you filter parts by Make, Model, Version and Year (we deliberately do not use a registration-number filter to avoid incorrect database links). After you place your order our specialists perform a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for the inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW/Novitec, Ragazzon/Remus/Ulter exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a trouble-free MOT in the Netherlands and vehicle inspection in Belgium.

What are the terms for cancellation and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior checking of Make/Model/Version restocking fees of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Alfa Romeo Giulietta QV or Veloce (1750 TBi 235 / 240 hp), would you like advice on 330mm Brembo caliper clearance, OZ Racing wheels or track spacers, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl