Model generation Type 955 (2009-2018) | 1.4 MultiAir Turbo (170 hp / 250 Nm) | Alfa DNA Active Suspension & Brembo Brakes

Why is correct wheel fitment crucial for the Alfa Romeo MiTo Quadrifoglio Verde / Veloce?
The Alfa Romeo MiTo Quadrifoglio Verde (QV, later renamed MiTo Veloce, produced from 2009 to 2018 with an original price of approximately € 26.000,- to € 32.000,-) is the sporty flagship of Alfa Romeo's compact 3-door hatchback. Powered by the innovative 1.4-litre MultiAir turbo engine with 170 HP and 250 Nm torque, combined with the Alfa DNA system and active electronic dampers, the QV delivers stylish sportiness. The MiTo (Type 955) uses the Italian bolt pattern 4x98 with a 58.1 mm centre bore and M12x1.25 wheel bolts. Factory fitment for the QV is 17 inch Cloverleaf/Cinquefoor wheels (7.0J ET39 with 205/45 R17 tyres) or the optional 18 inch 'Telephone number' dial wheels (7.5J ET39 with 215/40 R18 tyres). Because the QV and Veloce come standard with red 305 mm 4-piston Brembo front calipers, they impose specific requirements on spoke clearance and offset when choosing aftermarket wheels. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Version, Year of manufacture and chassis number.
The image below shows an original alloy wheel from the Alfa Romeo MiTo QV with the recognisable round-hole design:
The values below represent the original factory parameters of the Alfa Romeo MiTo Quadrifoglio Verde and Veloce (955). Use these as a technical reference when purchasing new wheels or wheel spacers.
| Specification | Factory value (OEM) | Notes & Advice |
|---|---|---|
| PCD (Pitch Circle Diameter) | 4x98 | Specific Fiat/Alfa 4-bolt PCD. (4x100 wheels can only be used with eccentric sliding bolts). |
| Centre bore (CB) | 58.1 mm | Standard Fiat/Alfa hub bore. Use hub-centric rings when fitting wheels with a larger centre bore (e.g. 67.1 mm or 73.1 mm). |
| Wheel fastener type | M12 x 1.25 Conical Bolts | Torque of 100 Nm recommended by Alfa Romeo. |
| OEM Wheel sizes (17" Standard QV Cloverleaf) | 7.0J x 17 ET39 | Factory 17 inch alloy wheels in a square setup. |
| OEM Wheel sizes (18" Option QV Dial / Turbine) | 7.5J x 18 ET39 | Factory 18 inch iconic telephone-dial or turbine alloy wheels in Anthracite or Gloss Black. |
| OEM Tyre sizes | 205/45 R17 (on 17") / 215/40 R18 (on 18") | Supplied on Pirelli P Zero Nero, Michelin Pilot Sport 4 or Continental SportContact with XL load index. |
Do you want to give your Alfa Romeo MiTo QV a wider track, an aggressive Italian stance or save weight with flow formed wheels from brands like JR-Wheels (JR11 / JR30 / SL01), OZ Racing (Formula HLT / Ultraleggera / Superturismo LM), Japan Racing, Concaver, MSW, Autec, Sparco, Ragazzon or Maxton-styling? Below are the ideal sizes for scratch-free fitment, including when lowered with Eibach, H&R, Novitec or KW coilovers.
| Wheel diameter & construction | Position | Recommended wheel width (J) | Ideal ET value range | Recommended tyre size |
|---|---|---|---|---|
| 17 Inch (OEM+ Flush Street Performance Sweet Spot) | Front & Rear (Square) | 7.0J / 7.5J | ET30 - ET35 | 205/45 R17 (or 215/45 R17) |
| 18 Inch (OEM+ Flush Street Performance Sweet Spot) | Front & Rear (Square) | 7.5J / 8.0J | ET30 - ET35 | 215/40 R18 (or 225/35 R18) |
| 18 Inch (Aggressive Show & Wide Stance Setup) | Front & Rear (Square) | 8.0J | ET28 - ET32 | 215/40 R18 (Slight stretch on 8.0J) |
Do you want to push the original 17" or 18" QV factory wheels (7.0J/7.5J ET39) slightly further out to sit flush with the body arches?
In our spacious and professional workshop in Nijkerk we fit wheels, exhaust systems, bodykits and suspension on 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):
| Component / Labour | Labour rate (Excl. VAT) | Indicative fitting time |
|---|---|---|
| Complete Wheel Set Fitting & Balancing | € 75 - € 115 | 45 - 60 minutes |
| Front Spoiler / Bumper Lip / Splitter Fitting | € 80 - € 120 | 45 - 60 minutes |
| Side Skirts Set Fitting | € 103 - € 145 | 60 - 90 minutes |
| Rear Diffuser Fitting | € 95 - € 145 | 45 - 75 minutes |
| Roof Spoiler Extension / Boot Spoiler Fitting | € 55 - € 80 | 30 - 45 minutes |
| Sidebars Set Fitting (Commercial Vehicles / SUV) | € 145 - € 185 | 60 - 90 minutes |
| Bullbars Fitting (Commercial Vehicles / Pickups) | € 141 - € 190 | 60 - 90 minutes |
| Exhaust Tip (Axle-back / Cat-back) | € 128 - € 268 | 60 - 150 minutes |
Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, giving you 100% fitment guarantee, manufacturer warranty and MOT assurance.
In our webshop you filter parts by Brand, Type, Specification and Year (we deliberately do not use a licence plate filter to avoid incorrect database links). After you place your order our specialists carry out a manual check based on your vehicle details and chassis number. If in doubt we will request 1 to 2 photos of your brakes or wheel arches via WhatsApp or e-mail within 48 hours. Only after 100% approval will your order be processed or fitted.
Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW/Novitec, Ragazzon/Remus/Ulter exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT in the Netherlands and vehicle inspection in Belgium.
Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted tyre-and-wheel sets. When returning incorrectly ordered items without prior verification of Brand/Type/Specification, restocking charges of 25% to 40% may apply for inspection and repackaging.
Do you have specific questions about exact fitment for your Alfa Romeo MiTo QV or Veloce (1.4 MultiAir 170 hp), would you like advice on 305mm Brembo caliper clearance, OZ Racing wheels or track spacers, or would you like an all-in quote including workshop fitting in Nijkerk?