Wheel Fitment Guide - Audi SQ7 (4M / 4M.5 Facelift)

Wheel Fitment Guide - Audi SQ7 (4M / 4M.5 Facelift)

Model generations 4M Pre-Facelift & 4M.5 Facelift (2016-present) | 4.0 TFSI V8 (507 hp) & 4.0 TDI V8 BiTurbo EPC (435 hp) | Quattro MLB-Evo Platform

Wheels Fitment Guide Audi SQ7 4M Wheels 'N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Audi SQ7 (4M / 4M.5)?
The Audi SQ7 (Type 4M & 4M.5 Facelift) is the most impressive full-size High-Performance SUV in the Audi range. Powered by the potent 435 HP V8 BiTurbo diesel engine with Electric Powered Compressor (EPC) or the later 507 HP 4.0-litre V8 TFSI petrol engine, the SQ7 places extremely high demands on wheel load capacity (minimum 900-950 kg per wheel) and caliper clearance. Built on the MLB-Evo platform, the SQ7 uses the VAG bolt pattern 5x112 with a 66.5 mm centre bore. Factory-fitted SQ7s ride on 20 inch (9.0J ET33), 21 inch (9.5J ET31) or 22 inch (10.0J ET26) S-design alloy wheels in a square setup. When choosing aftermarket alloys (such as 10.0J or 10.5J on 22 or 23 inch) a precisely calculated offset (ET18-ET26) is crucial for a tight flush fitment without tyre rubbing during compression on S-air suspension, combined with sufficient spoke clearance around the massive 400 mm / 420 mm 6-piston brakes. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Trim, Year and chassis number.

1. Factory specifications (OEM) Audi SQ7 4M / 4M.5

The values below represent the original factory parameters of the Audi SQ7 (4M Pre-Facelift & 4M.5 Facelift). Use these as a technical reference when purchasing new wheels or spacers.

Specification Factory value (OEM) Explanation & Advice
Bolt pattern (PCD) 5x112 Standard VAG 5-lug bolt circle on the MLB-Evo platform.
Centre bore (CB) 66.5 mm Large VAG MLB-Evo hub bore. Hub centring rings are required for wheels with a larger centre bore (e.g. 73.1 mm).
Wheel fastener type M14 x 1.5 Ball-conical Bolts Torque of 160 Nm recommended by Audi.
OEM Wheel sizes (21" Standard SQ7) 9.5J x 21 ET31 Factory 5-V-spoke S-design alloy wheels in a square fitment arrangement.
OEM Wheel sizes (22" Audi Sport Option) 10.0J x 22 ET26 Factory 5-arm trapezoid or 5-V-spoke Audi Sport wheels.
OEM Tyre sizes 285\/45 R20 (on 20") \/ 285\/40 R21 (on 21") \/ 285\/35 R22 (on 22") Supplied on Continental SportContact 6, Pirelli P Zero SUV or Hankook Ventus S1 evo3 SUV with XL Load Index (108-111 XL).

2. Aftermarket Fitment Guide (21", 22" & 23")

Do you want to give your Audi SQ7 an even tighter wheel-filling look, deeper concavity or weight savings with Flow Formed / Custom Forged wheels from brands like Concaver, JR-Wheels, Rotiform, Veemann, Vossen, OZ Racing, BC Forged or Maxton-styling? Below are the ideal sizes for a scratch-free fit, including on cars with S-air suspension.

Wheel diameter Recommended Wheel width (J) Ideal ET Range Recommended Tyre size Fitment Characteristic
21 Inch (OEM+ Winter / Comfort Setup) 9.5J / 10.0J ET22 - ET28 285/40 R21 Maintains optimal ride comfort while nicely filling the wheel arch.
22 Inch (Absolute Sweet Spot Street Performance) 10.0J / 10.5J ET20 - ET25 285\/35 R22 (or 295\/35 R22) The most chosen size for the SQ7. Fills the arches flush with deep concavity.
23 Inch (Exclusive Wide Flush SUV Show Stance) 10.5J / 11.0J ET18 - ET22 295\/30 R23 (or 305\/30 R23) Extremely impressive visual impact. 100% scratch-free on standard and air suspension.

3. Wheel Spacers & Bolt Pattern Adapters for Audi SQ7 4M

Do you want to push the original 21" or 22" S-line factory wheels (9.5J ET31 / 10.0J ET26) slightly further out to sit flush with the fenders?

  • Wheel spacers: On the original factory wheels, H&R or Eibach spacers of 12 mm to 15 mm at the front and 15 mm to 18 mm at the rear can be fitted. Use only hub-centric aluminium spacers with the specific 66.5 mm hub fitment and extended M14x1.5 wheel bolts.
  • Bolt pattern adapters & Fitment check: Do you have an exclusive custom wheel set in mind with a different bolt pattern (e.g. 5x112 to 5x130)? Bolt pattern adapters compensate for this but have a minimum thickness of 15 mm to 20 mm. Our fitment specialists in Nijkerk calculate the total effective ET in advance to prevent wide tyres rubbing the wheel arch lips when the suspension is compressed at speed.

4. Fixed Labour Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we mount wheels, exhaust systems, bodykits and suspension daily on 2 to 5 cars. We apply transparent fixed rates (excl. VAT):

Part / Labour Labour rate (Excl. VAT) Indicative Labour time
Complete Wheel set Mounting & Balancing € 75 - € 115 45 - 60 minutes
Front spoiler / Bumper lip / Splitter Fitting € 80 - € 120 45 - 60 minutes
Side Skirts Set Fitting € 103 - € 145 60 - 90 minutes
Rear diffuser Fitting € 95 - € 145 45 - 75 minutes
Roof spoiler extension / Boot spoiler Fitting € 55 - € 80 30 - 45 minutes
Sidebars Set Fitting (Commercial vans / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Fitting (Commercial vans / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust connection (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-movers"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, giving you 100% fitment guarantee, manufacturer warranty and MOT certainty.

How does the vehicle check and fitment guarantee of Wheels 'N Customs work?

In our webshop you filter parts by Make, Model, Variant and Year (we consciously do not use a licence-plate filter to avoid incorrect database links). After you place your order our specialists carry out a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or email for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for inspection?

Yes. Almost all our alloy wheels, lowering kits from Eibach/H&R/KW, Milltek/Remus exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a trouble-free MOT in the Netherlands and vehicle inspection in Belgium.

What are the conditions for withdrawal and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior verification of Make/Model/Variant, restocking costs of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Audi SQ7 (4M / 4M.5), would you like advice about 400mm S-caliper clearance or load capacity requirements, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl