Wheel Fitment Guide - Audi SQ8 (4M / 4M.5 Facelift)

Wheels Fitment Guide - Audi SQ8 (4M / 4M.5 Facelift)

Model generations 4M Pre-Facelift & 4M.5 Facelift Coupe-SUV (2019-present) | 4.0 TFSI V8 (507 hp) & 4.0 TDI V8 BiTurbo EPC (435 hp) | Quattro MLB-Evo Platform

Wheels Fitment Guide Audi SQ8 4M Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Audi SQ8 (4M / 4M.5)?
The Audi SQ8 (Type 4M & 4M.5 Facelift) is the sporty and athletic coupe-SUV sibling of the SQ7. Powered by the potent 435 HP V8 BiTurbo diesel with Electrically Driven Compressor (EPC) or the later 507 HP 4.0-litre V8 TFSI petrol engine, the SQ8 places high demands on wheel load rating (minimum 900-950 kg per wheel) and caliper clearance. Built on the MLB-Evo platform, the SQ8 uses the VAG bolt pattern 5x112 with a 66.5 mm centre bore. Factory-fit SQ8s sit on 21 inch (9.5J ET31) or 22 inch (10.0J ET21 / 10.0J ET26) S-design alloy wheels in a square setup. When choosing aftermarket alloys (such as 10.0J or 10.5J on 22 or 23 inch) an accurately calculated offset (ET18-ET25) is crucial for a tight flush fit without tyre rubbing when compressing on S-air suspension, combined with sufficient spoke clearance around the large 400 mm / 420 mm 6-pot brakes. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Trim, Year and chassis number.

1. Factory specifications (OEM) Audi SQ8 4M / 4M.5

The values below represent the original factory parameters of the Audi SQ8 (4M Pre-Facelift & 4M.5 Facelift). Use these as a technical reference when purchasing new wheels or spacers.

Specification Factory Value (OEM) Notes & Advice
Bolt Pattern (PCD) 5x112 Standard VAG 5-bolt circle on the MLB-Evo platform.
Centre Bore (CB) 66.5 mm Large VAG MLB-Evo hub bore. Centre rings required for wheels with a larger hub diameter (e.g. 73.1 mm).
Wheel Fastening Type M14 x 1.5 Ball Conical Bolts Torque of 160 Nm recommended by Audi.
OEM Wheel Sizes (21" Standard SQ8) 9.5J x 21 ET31 Factory 5-V-spoke S-design alloy wheels in square setup.
OEM Wheel Sizes (22" Audi Sport Option) 10.0J x 22 ET21 \/ 10.0J x 22 ET26 Factory 5-arm trapezoid or 5-V-spoke Audi Sport wheels.
OEM Tyre Sizes 285\/45 R20 (on 20") \/ 285\/40 R21 (on 21") \/ 285\/35 R22 (on 22") Supplied on Continental SportContact 6, Pirelli P Zero SUV or Hankook Ventus S1 evo3 SUV with XL Load Index (108-111 XL).

2. Aftermarket Fitment Guide (21", 22" & 23")

Do you want to give your Audi SQ8 a tighter fill of the wheel arches, deeper concavity or weight savings with Flow Formed \/ Custom Forged wheels from brands like Concaver, JR-Wheels, Rotiform, Veemann, Vossen, OZ Racing, BC Forged or Maxton-styling? Below you will find the ideal sizes for a scratch-free fit, also for cars with S-air suspension.

Wheel Diameter Recommended Wheel Width (J) Ideal ET Range Recommended Tyre Size Fitment Characteristics
21 Inch (OEM+ Winter \/ Comfort Setup) 9.5J / 10.0J ET22 - ET28 285/40 R21 Preserves optimal ride comfort with a nicely filled wheel arch.
22 Inch (Absolute Sweet Spot Street Performance) 10.0J / 10.5J ET18 - ET24 285\/35 R22 (or 295\/35 R22) The most chosen size for the SQ8. Fills the arches flush with deep concavity.
23 Inch (Exclusive Wide Flush SUV Show Stance) 10.5J / 11.0J ET16 - ET22 295\/30 R23 (or 305\/30 R23) Extremely impressive visual impact. 100% scratch-free on standard and air suspension.

3. Spacers & Bolt Pattern Adapters for Audi SQ8 4M

Do you want to push the original 21" or 22" S-line factory wheels (9.5J ET31 \/ 10.0J ET21) slightly further out to make them sit flush with the fenders?

  • Spacers: On the original factory wheels, H&R or Eibach spacers of 12 mm to 15 mm at the front and 15 mm to 18 mm at the rear can be fitted. Use only hub-centred aluminium spacers with the specific 66.5 mm hub bore and extended M14x1.5 wheel bolts.
  • Bolt Pattern Adapters & Fitment Check: Do you have an exclusive custom wheelset in mind with a different bolt pattern (e.g. 5x112 to 5x130)? Bolt pattern adapters accommodate this but have a minimum thickness of 15 mm to 20 mm. Our fitment specialists in Nijkerk calculate the total effective ET in advance to prevent wide tyres from contacting the wheel arch lips during compression at speed.

4. Fixed Labour Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we install wheels, exhausts, bodykits and suspension on 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):

Part \/ Operation Labour Rate (Excl. VAT) Indicative Installation Time
Complete Wheel Set Mounting & Balancing € 75 - € 115 45 - 60 minutes
Front Splitter \/ Bumper Lip \/ Splitter Installation € 80 - € 120 45 - 60 minutes
Side Skirts Set Installation € 103 - € 145 60 - 90 minutes
Rear Diffuser Installation € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Boot Spoiler Installation € 55 - € 80 30 - 45 minutes
Sidebars Set Installation (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Installation (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Tip (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-shifters"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, which gives you 100% fitment guarantee, factory warranty and MOT certainty.

How does the vehicle inspection and fitment guarantee from Wheels 'N Customs work?

In our webshop you filter parts by Brand, Type, Trim and Year (we deliberately do not use a licence plate filter to avoid incorrect database links). After placing your order our specialists perform a manual check based on your vehicle data and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for inspection?

Yes. Almost all our alloy wheels, lowering kits from Eibach/H&R/KW, Milltek/Remus exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT in the Netherlands and vehicle inspection in Belgium.

What are the terms for withdrawal and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, bespoke drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior verification of Brand/Type/Trim, restocking fees of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Audi SQ8 (4M / 4M.5), would you like advice on 400mm S-caliper clearance or load rating requirements, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl