Wheel Fitment Guide - Ford Focus ST250 (MK3 / MK3.5 2.0 EcoBoost 250 hp)

Wheels Fitment Guide - Ford Focus ST250 (MK3 / MK3.5 2.0 EcoBoost 250 hp)

Model generation MK3 & MK3.5 Facelift (2012-2018) | 2.0 EcoBoost Turbo (250 hp / 360 Nm Overboost) | Torque Vectoring Control & ST Performance Chassis

Wheels Fitment Guide Ford Focus ST250 MK3 Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Ford Focus ST250 (MK3 / MK3.5)?
The Ford Focus ST250 (MK3 pre-facelift and MK3.5 facelift, produced from 2012 to 2018 with an original new price of approximately € 35.000,- to € 41.000,-) is one of Europe’s most highly regarded hot hatches and sportswagons. Powered by the fiery 2.0-litre EcoBoost 4-cylinder turbo engine with 250 HP and 360 Nm overboost torque, the ST250 delivers impressive performance. The car uses the 5x108 bolt pattern with a 63.4 mm centre bore and M12x1.5 wheel bolts. Factory-fitted, the ST250 rides on 18 inch Rock Metallic or Silver Y-spoke wheels (8.0J ET55 with 235/40 R18 tyres) or the optional 19 inch 5-spoke wheels on the Facelift model (8.0J ET55 with 235/35 R19 tyres). Because the factory offset is very high (ET55), the original wheels sit relatively far inboard. When choosing aftermarket wheels (such as 18x8.0J or 18x8.5J with ET40 to ET48) the arches are filled tight and flush. This pairs perfectly with Milltek/Remus/Cobalt cat-back exhaust systems and Maxton Design front splitters. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Trim, Year and chassis number.

The image below shows an original alloy wheel from Ford Performance, similar to the fitments on the Focus ST250 platform:

Original Ford Performance alloy wheel with specific fitment

1. Factory Specifications (OEM) Ford Focus ST250 MK3

The values below represent the original factory parameters of the Ford Focus ST250 (MK3 / MK3.5 2.0 EcoBoost). Use these as a technical reference when purchasing new wheels or wheel spacers.

Specification Factory Value (OEM) Notes & Advice
P.C.D. (Pitch Circle Diameter) 5x108 Standard Ford 5-bolt circle on the C1 platform.
Centre Bore (CB) 63.4 mm Standard Ford hub bore. Use hub-centric rings when fitting wheels with a larger centre bore (e.g. 67.1 mm or 73.1 mm).
Wheel Fastening Type M12 x 1.5 Conical Nuts Torque of 135 Nm recommended by Ford Performance.
OEM Wheel Sizes (18" Standard ST Y-Spoke) 8.0J x 18 ET55 Factory 18 inch Rock Metallic or Silver alloy wheels in a square setup.
OEM Wheel Sizes (19" Option Facelift ST) 8.0J x 19 ET55 Factory 19 inch 5-spoke alloy wheels in Gloss Black / Polished finish.
OEM Tyre Sizes 235/40 R18 (on 18") / 235/35 R19 (on 19") Supplied on Goodyear Eagle F1 Asymmetric 2 or Michelin Pilot Sport 4 with XL load rating.

2. Aftermarket Fitment Guide (18" & 19" Focus ST250 MK3)

Do you want to fit your Ford Focus ST250 MK3 or MK3.5 with a wider track, a sportier stance or weight savings using Flow Formed wheels from brands such as Mountune (m-Spec), Team Dynamics (Pro Race 1.2 in 5x108), JR-Wheels (JR11 / JR21 / JR30 / SL01), Concaver, OZ Racing (Ultraleggera / Superturismo LM), Motec (Ultralight), Autec (Wizard), Sparco, Milltek, Remus or Maxton Styling? Below are the ideal sizes for a scratch-free fit, also when lowered with Eibach, H&R or KW V1/V3 coilovers.

Wheel Diameter & Construction Position Recommended Rim Width (J) Ideal ET Range Recommended Tyre Size
18 Inch (OEM+ Flush Street Performance Sweet Spot) Front & Rear (Square) 8.0J / 8.5J ET40 - ET48 235/40 R18 (or 245/40 R18)
18 Inch (Aggressive Fast Road & Trackday Setup) Front & Rear (Square) 8.5J / 9.0J ET38 - ET42 235/40 R18 (or 245/40 R18 Semi-slicks Nankang NS-2R)
19 Inch (Show & Performance Stance Setup) Front & Rear (Square) 8.5J ET42 - ET45 235/35 R19 (or 245/35 R19)

3. Wheel Spacers & Fitment Determinations for Focus ST250 MK3

Do you want to move the original 18" or 19" ST factory wheels with their high offset (8.0J ET55) slightly outwards to make them sit flush with the arches?

  • Wheel Spacers: On the original 8.0J ET55 factory wheels, H&R, Eibach or Mountune spacers from 12 mm to 15 mm can be fitted at the front and 15 mm to 20 mm at the rear. Use only hub-centric aluminium spacers with the specific 5x108 bolt pattern and 63.4 mm centre bore, with extended M12x1.5 wheel studs.
  • 320mm ST Front Brake Clearance: The Focus ST250 is fitted with ventilated 320 mm discs at the front. When selecting alloy wheels with a low offset between ET40 and ET48 there is ample spoke clearance around the brake calipers.

4. Fixed Labour Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we fit wheels, exhausts, bodykits and suspension on 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):

Part / Labour Labour Rate (Excl. VAT) Indicative Fitting Time
Complete Wheel Set Mounting & Balancing € 75 - € 115 45 - 60 minutes
Front Spoiler / Bumper Lip / Splitter Mounting € 80 - € 120 45 - 60 minutes
Side Skirts Set Mounting € 103 - € 145 60 - 90 minutes
Rear Diffuser Mounting € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Boot Lip Mounting € 55 - € 80 30 - 45 minutes
Sidebars Set Mounting (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Mounting (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Tailpipe (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-movers"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with our own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, giving you 100% fitment guarantee, factory warranty and MOT certainty.

How does Wheels 'N Customs' vehicle check and fitment guarantee work?

In our webshop you filter parts by Make, Type, Variant and Year (we deliberately do not use a licence-plate filter to avoid incorrect database links). After you place your order our specialists carry out a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW/Mountune, Milltek/Remus/Cobra exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT inspection in the Netherlands and vehicle inspection in Belgium.

What are the terms for withdrawal and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior verification of Make/Type/Variant restocking fees of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Ford Focus ST250 (MK3 / MK3.5 2.0 EcoBoost 250 hp), would you like advice on 18 or 19 inch Mountune / OZ Racing wheels or track widening spacers, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl