Model generation H247 Crossover SUV (2020-present) | 2.0 Turbo M139 (387 hp & 421 hp GLA 45 S) | AMG Performance 4MATIC+ Widebody

Why is correct wheel fitment crucial for the Mercedes-AMG GLA 45 & GLA 45 S (H247)?
The Mercedes-AMG GLA 45 and GLA 45 S 4MATIC+ (Type H247) combine the practicality of a compact SUV with the extreme performance of a super-hothatch. Powered by the most powerful series-produced four-cylinder engine in the world (M139 2.0-litre turbo engine with 421 HP in the S version) and AMG Torque Control all-wheel drive, the GLA 45 S imposes very specific demands on wheel choice. The GLA 45 (S) features widened wheel arches and a broader track. The car uses the bolt pattern 5x112 with a 66.6 mm centre bore and M14x1.5 wheel bolts. From the factory the GLA 45 S rides on 20 inch wheels (8.5J ET40) or optional 21 inch wheels (8.5J ET40 on forged AMG multi-spoke wheels with 255/35 R21 tyres). For aftermarket alloys (such as 8.5J or 9.0J width on 20 or 21 inch) spoke clearance around the large 360 mm 6‑piston AMG brakes is essential, combined with a considered offset (ET35‑ET42) to properly fill the wheel arches. At Wheels 'N Customs in Nijkerk we pre-check every order based on your selected Make, Model, Specification, Year of manufacture and chassis number.
The values below represent the original factory parameters for the Mercedes-AMG GLA 45 & GLA 45 S (H247 SUV). Use these as a technical reference when purchasing new wheels or wheel spacers.
| Specification | Factory Value (OEM) | Notes & Advice |
|---|---|---|
| Pitch Circle Diameter (PCD) | 5x112 | Standard Mercedes-Benz 5-bolt PCD on the MFA2 platform. |
| Centre Bore (CB) | 66.6 mm | Mercedes-Benz hub bore. Hub rings required for wheels with larger centre bores (e.g. 73.1 mm). |
| Wheel Fastening Type | M14 x 1.5 Ball Conical Bolts | A tightening torque of 130 Nm is recommended by Mercedes-AMG. |
| OEM Wheel Sizes (19" GLA 45 Standard) | 8.5J x 19 ET46 | Factory 10-spoke two-tone alloy wheels in a square setup. |
| OEM Wheel Sizes (20" GLA 45 S Standard Cross-Spoke) | 8.5J x 20 ET40 | Factory 20-inch AMG forged matte black 5-twin-spoke wheels. |
| OEM Wheel Sizes (21" GLA 45 S Option Multi-Spoke) | 8.5J x 21 ET40 | Factory 21-inch AMG forged matte black or two-tone Multi-Spoke wheels. |
| OEM Tyre Sizes | 255/45 R19 (19") / 255/40 R20 (20") / 255/35 R21 (21") | Supplied on Michelin Pilot Sport 4S SUV or Continental SportContact 6 with XL load index and MO1 (Mercedes-AMG OEM spec). |
Would you like to give your Mercedes-AMG GLA 45 or GLA 45 S H247 a tighter fill of the widebody wheel arches, a sportier stance or weight savings using Flow Formed / Forged wheels from brands such as Concaver, JR-Wheels (SL01 / JR11 / JR30), Rotiform, Veemann, Motec, Borbet, OZ Racing or Maxton-styling? Below are the ideal sizes for a scratch-free fit, also when lowered with Eibach, H&R or KW coilovers.
| Wheel Diameter & Construction | Position | Recommended Rim Width (J) | Ideal ET Range | Recommended Tyre Size |
|---|---|---|---|---|
| 19 Inch (OEM+ Winter / Comfort Setup) | Front & Rear (Square) | 8.5J | ET38 - ET42 | 255/45 R19 |
| 20 Inch (Absolute Street Performance Sweet Spot) | Front & Rear (Square) | 8.5J / 9.0J | ET35 - ET40 | 255/40 R20 |
| 21 Inch (Exclusive Show Performance Stance) | Front & Rear (Square) | 8.5J / 9.0J | ET35 - ET40 | 255/35 R21 (or 265/35 R21) |
Would you like to push the original 20" or 21" AMG wheels (8.5J ET40) further outwards so they sit flush with the wide wings?
In our spacious and professional workshop in Nijkerk we fit wheels, exhausts, bodykits and suspensions daily on 2 to 5 cars. We apply transparent fixed rates (excl. VAT):
| Part / Labour | Labour Rate (Excl. VAT) | Indicative Fitment Time |
|---|---|---|
| Complete Wheel Set Mount & Balance | € 75 - € 115 | 45 - 60 minutes |
| Front Spoiler / Bumper Lip / Splitter Fitment | € 80 - € 120 | 45 - 60 minutes |
| Side Skirts Set Fitment | € 103 - € 145 | 60 - 90 minutes |
| Rear Diffuser Fitment | € 95 - € 145 | 45 - 75 minutes |
| Roof Spoiler Extension / Boot Lip Spoiler Fitting | € 55 - € 80 | 30 - 45 minutes |
| Sidebars Set Fitting (Commercial Vehicles / SUV) | € 145 - € 185 | 60 - 90 minutes |
| Bullbars Fitting (Commercial Vehicles / Pickups) | € 141 - € 190 | 60 - 90 minutes |
| Exhaust Tailpipe (Axle-back / Cat-back) | € 128 - € 268 | 60 - 150 minutes |
Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, which gives you 100% fitment guarantee, factory warranty and MOT (APK) certainty.
In our webshop you filter parts by Make, Model, Version and Year (we deliberately do not use a licence plate filter to avoid incorrect database links). After placing your order our specialists perform a manual check based on your vehicle details and chassis number. If there is doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.
Yes. Almost all our alloy wheels, lowering kits from Eibach/H&R/KW, Remus/Milltek/Akrapovi? exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a worry-free MOT (APK) in the Netherlands and vehicle inspection in Belgium.
Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially made-to-measure items, bespoke drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior verification of Make/Model/Version restocking fees of 25% to 40% may apply for inspection and repackaging.
Do you have specific questions about exact fitment for your Mercedes-AMG GLA 45 or GLA 45 S 4MATIC+ (H247), would you like advice about AMG 6-piston caliper clearance or track wideners, or would you like an all-in quote including workshop fitting in Nijkerk?