Wheel Fitment Guide - Volkswagen Arteon R & Shooting Brake (3H9 2.0 TSI 320 hp 4MOTION)

Wheel Fitment Guide - Volkswagen Arteon R & Shooting Brake (3H9 2.0 TSI 320 hp)

Model generation 3H9 (2020-2026) | 2.0 TSI EA888 EVO4 (320 hp / 420 Nm) | R-Performance Torque Vectoring 4MOTION, DCC Dynamic Chassis & 18" R Brakes

Wheel Fitment Guide Volkswagen Arteon R Shooting Brake Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Volkswagen Arteon R & Shooting Brake (3H9)?
The Volkswagen Arteon R and Arteon R Shooting Brake (3H9 generation, produced from 2020 with an original new price of approximately € 63,900 to € 68,800) are Volkswagen’s sporty flagships. Powered by the high-output 2.0-litre TSI EA888 EVO4 turbo engine with 320 hp and 420 Nm of torque, a 7-speed DSG automatic, R-Performance Torque Vectoring 4MOTION (with drift mode on the rear axle) and standard DCC adaptive dampers, the Arteon R accelerates from 0-100 km/h in 4.9 seconds. The Arteon R uses the well-known VAG bolt pattern 5x112 with a 57.1 mm centre bore and M14x1.5 ball-seat wheel bolts. Because the 3H9 chassis has wider wheel arches than the Golf R, the Arteon R requires lower offsets (ET38 to ET40 for 8.0J/8.5J widths). From the factory, the Arteon R sits on 19 inch 'Adelaide' alloy wheels (8.0J x 19 ET40 with 245/40 R19) or optional 20 inch 'Estoril' wheels in Gloss Black or Diamond Turned (8.0J x 20 ET40 with 245/35 R20 Pirelli P Zero / Continental SportContact 6 tyres). To house the distinctive blue R brake callipers and 357 mm perforated two-piece 'Pin-Disc' rotors up front and prevent rubbing, precise wheel selection is required. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Variant, Year and VIN.

1. Factory specifications (OEM) Volkswagen Arteon R 3H9

The values below represent the original factory parameters of the Volkswagen Arteon R & Shooting Brake (3H9 2.0 TSI 320 hp 4MOTION). Use these as a technical reference when purchasing new wheels or spacers.

Specification Factory value (OEM) Explanation & Advice
Bolt pattern (PCD) 5x112 Standard VAG 5-lug bolt circle on the MQB-B platform.
Centre bore (CB) 57.1 mm Standard VW MQB centre bore. Spigot rings needed for wheels with a larger centre bore (e.g. 66.6 mm or 73.1 mm).
Wheel fastening type M14 x 1.5 Ball-seat Bolts Tightening torque of 120 Nm recommended by Volkswagen R GmbH.
OEM Wheel Sizes (19" Standard Adelaide R) 8.0J x 19 ET40 All round (Square) Factory 19 inch two-tone R alloy wheels in a Square setup.
OEM Wheel Sizes (20" Option Estoril / Black Performance) 8.0J x 20 ET40 All round (Square) Factory 20 inch R alloy wheels in Gloss Black or Machined finish.
OEM Tyre Sizes 245/40 R19 (19") / 245/35 R20 (20") Supplied on Pirelli P Zero, Continental SportContact 6 or Goodyear Eagle F1 SuperSport with XL Load Index.

2. Aftermarket Fitment Guide (19" & 20" Arteon R 3H9)

Would you like to equip your Volkswagen Arteon R or Shooting Brake with a tighter wheel-arch fill, sportier concavity or weight saving using Flow Formed / Custom Forged wheels from brands such as OZ Racing (Superturismo Dakar / Ultraleggera HLT in 5x112), BBS (CH-R / CI-R / SR), Rotiform (LAS-R / RSE / KPS), JR-Wheels (JR21 / JR30 / SL01), Concaver (CVR1 / CVR3), Remus, Milltek, Akrapovi?, APR or Maxton styling? Below you can find the ideal sizes for a rub-free fitment around the 357 mm 2-piece R brakes.

Inch size & Configuration Position Recommended Wheel Width (J) Ideal Offset (ET) Range Recommended Tyre Size
19 Inch (Lightweight Street / Winter Square Sweet Spot) Front & Rear (Square) 8.0J / 8.5J ET35 - ET42 245/40 R19 All round
20 Inch (OEM+ Flush Fast Road Square Sweet Spot) Front & Rear (Square) 8.5J / 9.0J ET35 - ET40 245/35 R20 or 255/35 R20 All round
20 Inch (Aggressive Deep Concave / Stance Setup) Front & Rear (Square) 9.0J / 9.5J ET33 - ET38 255/35 R20 All round (Tightly fills the Arteon R's hips)

3. Spacers & Fitment Requirements for Arteon R 3H9

Do you want to push the original 19" or 20" Adelaide/Estoril R factory wheels (8.0J ET40) further out to make them sit flush with the fender edges?

  • Spacers: On the original 8.0J ET40 factory wheels, H&R, Eibach or Billet Aluminium spacers from 10 mm to 12 mm at the front and 12 mm to 15 mm at the rear can be installed. Use only hub-centric aluminium spacers with the specific 5x112 bolt pattern and 57.1 mm centre bore with extended M14x1.5 ball-seat wheel bolts.
  • 357mm 2-Piece R Brakes Clearance: The Arteon R features front 2-piece 357 mm 'Pin-Disc' floating discs and blue R calipers. When selecting aftermarket 19 or 20 inch alloy wheels, ample spoke clearance around the front calipers is required.

4. Fixed Installation Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we fit wheels, exhaust systems, body kits and suspension on 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):

Part / Task Installation Rate (Excl. VAT) Indicative Installation Time
Complete Wheel Set Installation & Balancing € 75 - € 115 45 - 60 minutes
Front Spoiler / Bumper Lip / Splitter Installation € 80 - € 120 45 - 60 minutes
Side Skirts Set Installation € 103 - € 145 60 - 90 minutes
Rear Diffuser Installation € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Bootlid Spoiler Installation € 55 - € 80 30 - 45 minutes
Sidebars Set Installation (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bull Bars Installation (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Fitment (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-shifters"?

Many e-commerce shops act purely as an intermediary without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and check the parts ourselves on a daily basis, which gives you a 100% fitment guarantee, manufacturer's warranty and APK assurance.

How does the vehicle check and fitment guarantee of Wheels 'N Customs work?

In our webshop you filter parts by Make, Model, Version and Year (we deliberately do not use a registration-plate filter to avoid incorrect database links). After you place your order our specialists perform a manual check based on your vehicle details and VIN. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 à 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or installed.

Are our fitted wheels and parts approved for the inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW, Remus/Milltek/Akrapovi? exhaust systems and body kits from Maxton Design have official German TÜV, ECE or ABE certification. This ensures a hassle-free APK inspection in the Netherlands and vehicle inspection in Belgium.

What are the conditions for withdrawal and returns (Directive 2011/83/EU)?

According to European Directive 2011/83/EU, for online purchases you have the right to withdraw your order within 14 days. Excluded from the right of withdrawal are specially custom-ordered items, custom drilled wheels (Custom ET/Blank) and mounted sets with tyres. When returning incorrectly ordered items without prior verification of Make/Model/Version, restock fees of 25% to 40% may apply for inspection and repackaging.

Get in Touch / Request Advice

Do you have specific questions about the exact fitment for your Volkswagen Arteon R or Arteon R Shooting Brake (3H9 2.0 TSI 320 hp 4MOTION), would you like advice on 357mm 2-piece R-caliper clearance, 19 or 20 inch OZ Racing / BBS / Rotiform wheels or spacers, or would you like to receive an all-in quote including workshop installation in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl