Wheel Fitment Guide: Volkswagen Polo GTI AW (2017-Present)
Why is accurate fitment essential for the Polo GTI AW?
The Polo AW sits on the MQB-A0 platform and unlike the larger Golf uses the 5x100 bolt pattern. Due to the sporty setup and larger 2.0 TSI brake calipers a precise ET is required. An ET that is too low will push the wheel against the inner wing when compressing, while the correct fitment provides a clean ‘flush’ look with maximum retention of ride comfort.
1. Original Factory Specifications (OEM Fits)
The OEM specifications below form the basis for the Polo GTI AW (including facelift models):
| Specification |
Factory Value (OEM) |
Expert Note |
| Bolt Pattern (PCD) |
5x100 |
Standard VAG compact-segment bolt pattern. |
| Centre Bore (CB) |
57.1 mm |
Precise hub fit. Use centring rings for larger centre bores (> 57.1 mm). |
| OEM Wheel Sizes |
17 and 18 Inch |
17" (Milton Keynes OEM) and 18" (Brescia / Faro OEM optional). |
| OEM ET Range |
ET46 - ET51 |
17x7.5J ET51 / 18x7.5J ET51 places the wheels slightly deeper in the wheelarch. |
| Wheel Fastening |
M14 x 1.5 Conical (R13) |
Note: Aftermarket wheels almost always use 60° conical wheel bolts! |
| Tightening Torque |
120 Nm |
Tighten with a calibrated torque wrench on clean hubs. |
2. Aftermarket Fitment Guide (What fits safely?)
Want the wheel to sit tighter against the arch ('flush fitment')? Use these proven sizes:
| Size |
Wheel Width (J) |
Ideal ET |
Recommended Tyre Size |
Fitment Character |
| 17 Inch |
17x7.5J / 17x8.0J |
ET38 - ET42 |
215/45 R17 |
Comfortable, perfect for daily and sporty use. |
| 18 Inch |
18x8.0J |
ET40 - ET45 |
215/40 R18 or 225/40 R18 |
Most popular fit! No rubbing and very tight fill. |
| 19 Inch |
19x8.0J |
ET45 |
215/35 R19 |
Show & Stance look. Visually maximally filled, low tyre sidewall. |
3. Wheel Spacers, Bolt Pattern Adapters & Lowering Advice
The Polo GTI AW is well suited to a sporty lowered stance combined with the correct track width.
- Wheel Spacers (Spacers): For original OEM 17" or 18" wheels (ET51) we recommend spacers of 10 mm per side (20 mm per axle) at the front and 12 mm to 15 mm per side (24–30 mm per axle) at the rear. This cancels out the deep-set look. Always use hub-centred spacers (57.1 mm) and longer M14x1.5 wheel bolts!
- Lowering (ST Suspensions / H&R / Eibach): The Polo GTI is factory-fitted slightly lower than a standard Polo, but an additional drop of 25–35 mm completes the look. With 18x8.0J ET42 fitted with lowering springs the wheel arch remains completely free from rubbing.
- Hub Adaptors (5x100 to 5x112): Because the choice of 5x112 wheels (such as original Golf R or Audi S3 wheels) is huge, hub adaptors are often used. With custom adaptors 15 mm thick, the bolt pattern can easily be changed to 5x112. Make sure the ET of the 5x112 wheel is sufficiently high (e.g. ET48–50) to provide compensation.
4. Frequently Asked Questions (FAQ)
Do 18 inch wheels rub on a lowered Polo GTI AW?
No, provided you choose a wheel size of 18x8.0J with an ET between ET40 and ET45 paired with 215/40 R18 tyres. Even with an H&R or Eibach 30 mm drop this wheel runs clear of the arches.
Do wheels from a Polo 6R / 6C fit directly on a Polo AW GTI?
The bolt pattern (5x100) and centre bore (57.1 mm) are identical. However, the Polo AW has wider track widths and larger wheel arches than the older 6R/6C generation. Wheels from a 6R often sit slightly deeper inboard on an AW, which can be easily resolved with small wheel spacers.
Which wheel bolts do I need for a set of aftermarket wheels?
Factory Volkswagen wheels use ball-cone (R13) bolts. For virtually all aftermarket brands (such as JR-Wheels, Rotiform, Concaver, Borbet) you must use 60° conical M14x1.5 wheel bolts. Fitting original ball-cone bolts into a conical seat is unsafe.
Have Your Fitment Checked By The Experts
Want to know which wheels, spacers or coilover kits suit your Volkswagen Polo GTI AW best? Contact our specialists in Nijkerk for free advice or ask your question in the shop.
Ask Our Experts For Advice