Wheel Fitment Guide - Dodge Charger SRT8 & SRT 392 (LD 6.4 V8 HEMI 477 hp / 485 hp)

Wheels Fitment Guide - Dodge Charger SRT8 & SRT 392 (LD 6.4 V8 HEMI)

Model generation LD (2012-2023) | 6.4 V8 HEMI 392 cu.in. (477 hp / 485 hp - 644 Nm) | TorqueFlite 8-Speed, Adaptive Damping Suspension & Brembo 6-Piston Brakes

Wheels Fitment Guide Dodge Charger SRT8 SRT 392 Wheels N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Dodge Charger SRT8 & SRT 392 (LD)?
\r\nThe Dodge Charger SRT8 and later SRT 392 (LD generation, produced from 2012 to 2023 with an original new price of approximately € 62.000,- to € 68.900,-) combine the practical convenience of a spacious 4-door sedan with the raw brute force of a classic American V8 Muscle Car. Powered by the legendary 6.4-litre (392 cubic inch) naturally aspirated HEMI V8 engine with 477 HP or 485 HP and 644 Nm torque, a TorqueFlite 8-speed automatic and a throaty active RWD exhaust, the Charger SRT accelerates to 100 km/h in 4.3 seconds. The Charger SRT uses the specific bolt pattern 5x115 with a 71.5 mm centre bore and M14x1.5 conical wheel nuts. Note: never fit universal 5x114.3 wheels onto a 5x115 Dodge hub to avoid vibrations. Factory-fitted, the SRT 392 sits on forged 20 inch W-Spoke or Slingshot alloy wheels (9.0J or 9.5J ET18.5 all round with 245/45 R20 or 275/40 R20 Pirelli P Zero Nero tyres). To clear the imposing 6-piston Brembo calipers and 390 mm vented/disc rotors at the front and to make use of the wide track width, a low ET value (ET15–ET25) is required. When selecting aftermarket or wide 22 inch staggered sets (such as 20x9.5J/10.5J or 22x9.5J/10.5J from Ferrada, Velgen Wheels, Vossen or Niche) the wheels sit aggressively and tightly in the arches. At Wheels 'N Customs in Nijkerk we check every order in advance based on your chosen Make, Model, Trim, Year and chassis number.

1. Factory specifications (OEM) Dodge Charger SRT8 / SRT 392

The values below represent the original factory parameters of the Dodge Charger SRT8 & SRT 392 (LD 6.4 V8 HEMI). Use them as a technical reference when purchasing new wheels or spacers.

Specification Factory value (OEM) Notes & Advice
Bolt pattern (PCD) 5x115 Standard Dodge / Chrysler LX/LD platform bolt circle. Use exactly 5x115 only!
Centre bore (CB) 71.5 mm Standard Dodge / Chrysler hub bore. Hub-centric rings required for wheels with a larger centre bore (e.g. 73.1 mm or 78.1 mm).
Wheel fastener type M14 x 1.5 Conical Nuts Torque of 150 Nm recommended by Street & Racing Technology (SRT).
OEM Wheel sizes (20" Forged Slingshot / W-Spoke) 9.0J x 20 ET18.5 or 9.5J x 20 ET18.5 All round (Square) Factory 20 inch forged alloy wheels in RWD configuration.
OEM Tyre sizes 245/45 R20 (on 9.0J) / 275/40 R20 (on 9.5J) Supplied on Pirelli P Zero Nero All-Season or Goodyear Eagle F1 SuperCar with XL Load Index.

2. Aftermarket Fitment Guide (20" & 22" Dodge Charger SRT)

Do you want to equip your Dodge Charger SRT8 or SRT 392 with a wider rear track, aggressive deep concavity or weight savings using Flow Formed / Custom Forged wheels from brands like Ferrada (FR1 / FR2 / FR4 in 5x115), Velgen Wheels (VMB5 / VF5), Vossen (HF-2 / HF-5), Niche, Borla, Corsa Performance, Stainless Works, Mopar or Maxton Styling? Below you’ll find the ideal sizes for a scratch-free fitment around the 390 mm 6-piston Brembo brakes.

Diameter & construction Position Recommended wheel width (J) Ideal ET range Recommended tyre size
20 Inch (OEM+ Flush Street Performance Wideset Sweet Spot) Front
\r\n Rear
9.5J Front
\r\n 10.5J Rear
ET15 - ET20
\r\n ET20 - ET25
275/40 R20 Front
305/35 R20 Rear (Mickey Thompson / Nitto NT555 G2)
22 Inch (OEM+ Flush Fast Road Wide Set Sweet Spot) Front
Rear
9.5J Front
10.5J Rear
ET15 - ET20
ET20 - ET25
265/30 R22 Front
295/30 R22 Rear
22 Inch (Aggressive Wide Deep Concave Wide Set) Front
Rear
9.5J Front
11.0J Rear
ET15 - ET18
ET18 - ET22
265/30 R22 Front
305/30 R22 Rear (Fills the arches maximally without scratching)

3. Wheel Spacers & Fitment Rules for Charger SRT

Do you want to push the original 20" SRT factory wheels (9.0J/9.5J ET18.5) slightly further out so they sit flush with the wheel arch edges?

  • Wheel Spacers (Spacers): On the original 9.0J/9.5J ET18.5 factory wheels you can fit H&R, Eibach or Billet Aluminium spacers from 10 mm to 12 mm at the front and 12 mm to 15 mm at the rear. Use only hub-centric aluminium spacers with the specific 5x115 bolt pattern and 71.5 mm hub bore with extended M14x1.5 wheel studs.
  • 390mm 6-Piston Brembo Clearance: The SRT 392 has gigantic 6-piston Brembo calipers up front. When selecting aftermarket 20 or 22 inch wheels you must check that the inner part of the wheel and the spokes clear the brake calipers.

4. Fixed Workshop Labour Rates Nijkerk

In our spacious and professional workshop in Nijkerk we daily fit wheels, exhaust systems, bodykits and suspensions on 2 to 5 cars. We apply transparent fixed rates (excl. VAT):

Part / Labour Fitting Rate (Excl. VAT) Indicative Fitting Time
Complete Wheel Set Fit & Balance € 75 - € 115 45 - 60 minutes
Front Spoiler / Bumper Lip / Splitter Fit € 80 - € 120 45 - 60 minutes
Side Skirts Set Fit € 103 - € 145 60 - 90 minutes
Rear Diffuser Fit € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Boot Spoiler Fit € 55 - € 80 30 - 45 minutes
Sidebars Set Fit (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Fit (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Connection (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-movers"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, giving you 100% fitment guarantee, factory warranty and MOT certainty.

How does the vehicle inspection and fitment guarantee from Wheels 'N Customs work?

In our webshop you filter parts by Brand, Type, Specification and Year (we deliberately do not use a licence-plate filter to avoid incorrect database matches). After you place your order our specialists perform a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for the inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW, Borla/Corsa/Stainless Works exhaust systems and bodykits from Maxton Design have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT inspection in the Netherlands and vehicle inspection in Belgium.

What are the terms for withdrawal and returns (Directive 2011/83/EU)?

Under the European Directive 2011/83/EU you have the right to withdraw your order within 14 days for online purchases. Excluded from the right of withdrawal are specially ordered made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted tyre-and-wheel sets. When returning incorrectly ordered items without prior verification of Brand/Model/Specification, restocking fees of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact 5x115 fitment for your Dodge Charger SRT8 or SRT 392 (LD 6.4 V8 HEMI 477 hp / 485 hp), would you like advice on 390mm 6-piston Brembo caliper clearance, 20 or 22 inch Ferrada / Velgen Wheels / Vossen wide sets or wheel spacers, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl