Wheels Fitment Guide - Kia Stinger GT (CK 3.3 T-GDI V6 TwinTurbo 366 hp / 370 hp AWD)

Wheels Fitment Guide - Kia Stinger GT (CK 3.3 T-GDI V6 TwinTurbo)

Model generation CK (2017-2023) | 3.3 T-GDI V6 TwinTurbo Lambda II (366 hp / 370 hp - 510 Nm) | Brembo High Performance Brakes & AWD Staggered Setup

Wheels Fitment Guide Kia Stinger GT CK Wheels 'N Customs Nijkerk Logo

Why is correct wheel fitment crucial for the Kia Stinger GT (CK)?
The Kia Stinger GT (CK generation with the 3.3‑litre V6 TwinTurbo engine, produced from 2017 to 2023 with an original new price of approximately € 59.900,- to € 68.500,-) redefined Kia’s image by offering a true Gran Turismo fastback. Powered by the 370 HP (366 HP after the 2021 facelift) 3.3 T‑GDI V6 engine producing 510 Nm of torque, an 8‑speed automatic, electronically controlled dampers and all‑wheel drive (AWD) with a rear‑biased setup, the Stinger GT accelerates to 100 km/h in 4.9 seconds. The Stinger GT uses the bolt pattern 5x114.3 with a 67.1 mm centre bore and M12x1.5 conical wheel nuts. Crucial for the Stinger GT is the factory Staggered (wide set) setup. From factory the Stinger GT rides on 19‑inch two‑tone alloy wheels (8.0J ET34 front with 225/40 R19 & 8.5J ET39.5 rear with 255/35 R19 Michelin Pilot Sport 4 tyres). To house the prominent red 4‑piston Brembo calipers and 350 mm ventilated front discs and to fill the muscular arches, an accurate ET value is required. At Wheels 'N Customs in Nijkerk we check every order in advance based on your selected Make, Model, Trim, Year and chassis number.

The photo below illustrates the red Brembo calipers and the original factory wheel of the Kia Stinger GT:

Kia Stinger GT factory wheel with red Brembo caliper and Michelin tyre

1. Factory specifications (OEM) Kia Stinger GT CK

The values below represent the original factory parameters of the Kia Stinger GT (CK 3.3 T‑GDI V6 TwinTurbo AWD). Use these as a technical reference when purchasing new wheels or wheel spacers.

Specification Factory value (OEM) Notes & Advice
Bolt pattern (PCD) 5x114.3 Standard Kia / Hyundai 5‑lug bolt circle on the CK platform.
Centre bore (CB) 67.1 mm Standard Kia / Hyundai centre bore. Hub centric rings required for wheels with a larger centre bore (e.g. 73.1 mm).
Wheel fastening type M12 x 1.5 Conical Nuts Torque of 110 Nm recommended by Kia Performance.
OEM Wheel sizes (19" Staggered GT Multi‑Spoke) 8.0J x 19 ET34 Front
8.5J x 19 ET39.5 Rear
Factory 19‑inch two‑tone alloy wide set on GT AWD models.
OEM Tyre sizes 225/40 R19 Front
255/35 R19 Rear
Supplied on Michelin Pilot Sport 4 or Continental SportContact 6 with XL load index.

2. Aftermarket Fitment Guide (19" & 20" Kia Stinger GT)

Do you want to fit a wider rear axle, deeper concavity or save weight with Flow Formed / Custom Forged wheels from brands such as JR‑Wheels (SL01 / JR21 / JR30 in 5x114.3), Concaver (CVR1 / CVR4), mbDESIGN (KV1), Vossen (HF‑2 / HF‑5), OZ Racing (Ultraleggera / Superturismo LM), Bastuck, Milltek, Remus, Eibach or Maxton‑styling? Below you’ll find the ideal sizes for scratch‑free clearance around the 350 mm 4‑piston Brembo brakes.

Wheel diameter & construction Position Recommended wheel width (J) Ideal ET value range Recommended tyre size
19 Inch (OEM+ Flush Street Performance wide set sweet spot) Front
Rear
8.5J Front
9.5J Rear
ET30 - ET35
ET35 - ET40
235/40 R19 Front
265/35 R19 Rear
20 Inch (OEM+ Flush Fast Road wide set sweet spot) Front
Rear
8.5J Front
9.5J or 10.0J Rear
ET30 - ET35
ET38 - ET42
245/35 R20 Front
275/30 R20 Rear
20 Inch (Aggressive Deep Concave / Stance Wide Set) Front
Rear
9.0J Front
10.0J or 10.5J Rear
ET28 - ET32
ET35 - ET40
245/35 R20 Front
285/30 R20 Rear (Slight stretch on 10.5J rear)

3. Spacers & Fitment Requirements for Stinger GT

Do you want to push the original 19" GT factory wheels (8.0J ET34 / 8.5J ET39.5) slightly further out to make them flush with the flanks of the fastback?

  • Spacers (Wheel Spacers): On the original factory wheels H&R, Eibach or Eibach Pro-Spacer kits of 12 mm to 15 mm at the front and 15 mm to 20 mm at the rear can be fitted. Use only hub-centred aluminium spacers with the specific 5x114.3 bolt pattern and 67.1 mm hub bore, with extended M12x1.5 wheel studs.
  • 350mm 4-Piston Brembo Clearance: The Stinger GT has large 4-piston Brembo calipers up front. When choosing aftermarket 19 or 20 inch alloy wheels there must be ample spoke clearance around the front calipers.

4. Fixed Labour Rates Workshop Nijkerk

In our spacious and professional workshop in Nijkerk we fit wheels, exhausts, bodykits and suspensions on 2 to 5 cars daily. We apply transparent fixed rates (excl. VAT):

Part / Work Labour Rate (Excl. VAT) Indicative Installation Time
Complete Wheel Set Fitting & Balancing € 75 - € 115 45 - 60 minutes
Front Spoiler / Bumper Lip / Splitter Fitting € 80 - € 120 45 - 60 minutes
Side Skirts Set Fitting € 103 - € 145 60 - 90 minutes
Rear Diffuser Fitting € 95 - € 145 45 - 75 minutes
Roof Spoiler Extension / Boot Spoiler Fitting € 55 - € 80 30 - 45 minutes
Sidebars Set Fitting (Commercial Vehicles / SUV) € 145 - € 185 60 - 90 minutes
Bullbars Fitting (Commercial Vehicles / Pickups) € 141 - € 190 60 - 90 minutes
Exhaust Connection (Axle-back / Cat-back) € 128 - € 268 60 - 150 minutes

5. Frequently Asked Questions & Legal Provisions

Why choose Wheels 'N Customs instead of online "box-shifters"?

Many e-commerce shops act purely as intermediaries without a physical workshop in Nijkerk or technical expertise. Wheels 'N Customs combines a webshop catalogue of more than 250,000 items with its own physical workshop in Nijkerk. We test, fit and inspect the parts ourselves on a daily basis, which gives you 100% fitment guarantee, factory warranty and MOT certainty.

How does Wheels 'N Customs vehicle inspection and fitment guarantee work?

In our webshop you filter parts by Brand, Model, Specification and Year (we deliberately do not use a registration-plate filter to avoid incorrect database links). After you place your order our specialists perform a manual check based on your vehicle details and chassis number. If in doubt we will ask you within 48 hours via WhatsApp or e-mail for 1 to 2 photos of your brakes or wheel arches. Only after 100% approval will your order be processed or fitted.

Are our fitted wheels and parts approved for inspection?

Yes. Virtually all our alloy wheels, lowering kits from Eibach/H&R/KW, Bastuck/Milltek exhaust systems and Maxton Design bodykits have official German TÜV, ECE or ABE certification. This guarantees a hassle-free MOT in the Netherlands and vehicle inspection in Belgium.

What are the conditions for withdrawal and returns (Directive 2011/83/EU)?

Under European Directive 2011/83/EU you have the right to withdraw from your online purchase within 14 days. Excluded from the right of withdrawal are specially made-to-measure items, custom-drilled wheels (Custom ET/Blank) and fitted sets with tyres. When returning incorrectly ordered items without prior inspection of Brand/Type/Specification, restocking fees of 25% to 40% may apply for inspection and repackaging.

Contact Us / Request Advice

Do you have specific questions about the exact fitment for your Kia Stinger GT (CK 3.3 T-GDI V6 TwinTurbo 366 hp / 370 hp), would you like advice on 19 or 20 inch JR-Wheels / Concaver / mbDESIGN wide sets or wheel spacers, or would you like an all-in quote including workshop fitting in Nijkerk?

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl