Wheel Fitment Guide: BMW 3 Series G20 / G21 (2019-Present)
Important shift with the BMW CLAR platform:
From the G20/G21 generation BMW switched from the traditional 5x120 PCD to the more modern 5x112 PCD with a larger centre bore of 66.6 mm. Old wheels from an F30/F31 therefore do not fit without adapters. Additionally, on xDrive models the correct ratio in tyre sizes between front and rear axle is crucial to preserve the transfer case.
1. Original Factory Specifications (OEM Fits)
The following data applies to the standard suspension and M-Sport suspensions of the BMW 3 Series G20 Sedan and G21 Touring (318i through M340i/M340d):
| Specification |
Factory Value (OEM) |
Expert Note |
| PCD (Bolt Pattern) |
5x112 |
Note: Not the old 5x120 from the F30 generation! |
| Centre Bore (CB) |
66.6 mm |
New BMW standard. Use hub rings if aftermarket wheel > 66.6 mm. |
| OEM Wheel Sizes |
17, 18, 19 and 20 Inch |
17"-18" (Standard/Luxury), 18"-19" (M-Sport), 20" (M Performance). |
| OEM ET Range |
ET25 - ET40 |
Depends on front or rear axle (OEM staggered sets have higher ET at the rear). |
| Wheel Fastening |
M14 x 1.25 Conical (60°) |
BMW uses M14x1.25 wheel bolts with a 60° conical seat. |
| Tightening Torque |
140 Nm |
Tighten accurately with a calibrated torque wrench. |
2. Aftermarket Fitment Guide (What fits safely?)
BMW drivers overwhelmingly choose a 'staggered setup' (wide set). The configurations below fit tightly within the wheel arch without rubbing:
| Size |
Wheel Width (J) |
Ideal ET Value |
Recommended Tyre Size |
Fitment Character |
| 18 Inch (Square) |
18x8.0J (Front & Rear) |
ET25 - ET30 |
225/45 R18 |
Comfortable daily setup, rotatable front to rear. |
| 19 Inch (Staggered) |
Front: 19x8.5J
Rear: 19x9.5J |
Front: ET25 - ET28
Rear: ET38 - ET40 |
Front: 225/40 R19
Rear: 255/35 R19 |
Most popular M-Sport setup! xDrive safe, very aggressive look. |
| 20 Inch (Staggered) |
Front: 20x8.5J \r\n\t\t\tRear: 20x9.5J |
Front: ET25 - ET28 \r\n\t\t\tRear: ET38 - ET40 |
Front: 225/35 R20 \r\n\t\t\tRear: 255/30 R20 |
M Performance & Stance look. Visually this fills the wheel arches maximally. |
3. Wheel Spacers, Bolt Pattern Adapters & Lowering Advice
The BMW G20/G21 comes from the factory with a fairly conservative tuck (wheels sit somewhat deep). With the right upgrades the car gets a more aggressive stance:
- Wheel Spacers (Spacers): For original M-Sport 18" or 19" wheels a spacer kit of 12 mm per side at the front and 15 mm per side at the rear is the golden standard. This brings the wheels exactly flush with the fender edges. Use only hub-centric spacers (66.6 mm) with extended M14x1.25 bolts!
- Lowering (Eibach / H&R / KW): A drop of 25 mm to 35 mm (using Eibach Pro-Kit or H&R lowering springs) transforms the appearance of the G20/G21. Combined with the above 19" or 20" width sets the wheel arch remains completely free from rubbing.
- Transferring old BMW Wheels (5x120)? If you want to fit an exclusive set of 5x120 wheels from an F30/E90 onto a G20 (5x112), you need bolt pattern adapters from 5x112 to 5x120. Since these adapters are at least 18 to 20 mm thick, the wheel must have a high base specification (e.g. ET45+) to prevent the wheel from sticking out too far.
4. Frequently Asked Questions (FAQ)
Can you just fit any width set to a BMW G20/G21 with xDrive?
No! On xDrive models (four-wheel drive) the difference in rolling circumference between the front and rear tyres may be a maximum of 1% (preferably as close to 0% as possible). Too large a difference overloads the electronic transfer case, which can lead to costly damage. Always use tyre size combinations approved by us such as 225/40 R19 front with 255/35 R19 rear.
Do wheels from a BMW F30 / F31 fit a BMW G20 / G21?
No, not directly. The F30 generation uses the old bolt pattern 5x120 with a centre bore of 72.5 mm, whereas the G20/G21 uses the new bolt pattern 5x112 with a centre bore of 66.6 mm. Installation is only possible using special bolt pattern adapter plates.
Does the G20 / G21 M340i / M340d have modified fitment requirements because of the brakes?
Yes. The M340i and M340d (and models with the M-Sport Bremsanlage / M Technology Package) are fitted with large 374 mm brake discs and 4‑piston calipers at the front. As a result not all 18 inch wheels will fit. With 18 inch the internal rim diameter and spoke clearance are critical. With 19 inch or 20 inch wheels you are guaranteed sufficient caliper clearance.
Need Advice For Your BMW G20 or G21?
Want to be 100% sure that the desired width set or wheel spacers will fit your BMW 3 Series without rubbing? Contact our fitment specialists in Nijkerk directly or ask your question via our webshop.
Ask Our Experts For Advice