It is every car enthusiast’s worst nightmare: you are pulled over during a large-scale technical roadside check (roadblock) by the Traffic unit or the ILT. The police inspect the car closely with decibel meters, wheel clearance tests and window light transmission testers. If serious technical violations are found, not only will you receive a hefty fine, the officer will also record a WOK status (Wachten Op Keuren) on the spot in the RDW registration database.
From that exact moment your car is no longer formally approved for use on public roads. You are no longer allowed to drive it, the insurance will no longer cover damage, and you must transport the car on a recovery truck to an official RDW inspection station for a costly reinspection. In the workshop of Wheels 'N Customs in Nijkerk we install exclusive wheels, lowering setups, bodykits and sports exhausts every day that meet the strictest admission requirements. In this legal and technical guide you will learn exactly what the police check, what tolerances are applied, and how to effectively prevent a WOK notification.
During a targeted check, the police assess a modified vehicle against the permanent requirements of the Vehicle Regulations:
Measurement with a calibrated decibel meter at 50 cm distance and 45 degrees from the exhaust. Maximum allowed is the registration value + 2 dB(A) measurement tolerance. Pops & bangs and valve control are tested immediately.
The wheels may protrude a maximum of 30 mm beyond the wheel arches. In addition, at full steering lock and under load the wheels must rotate completely free of inner liners and strut.
Front splitters, canards, diffusers and wings are tested for sharp edges (radius < 2.5 mm) and secure mounting. Universal aluminium wings with sharp corners are immediately prohibited.
Measurement of the windscreen and front side windows with the Tintman measuring device. A minimum of 55% light transmission is mandatory; below 50% the registration certificate is seized on the spot.
| Component / Aspect | Legally Permitted (100% Legal) | Immediate Risk of Fine or WOK Status |
|---|---|---|
| Exhaust noise (decibels) | Registration value + max. 2 dB(A) measurement tolerance (ECE sports exhaust) | > Registration value + 2 dB(A), straight pipe without silencers or open valves |
| Wheel protrusion (track width) | Max. 30 mm beyond the wing; tread covered in accordance with the guideline | > 30 mm beyond the edge, or wheels fouling the bodywork |
| Ride height & spring tension | Lowered with TÜV approval; springs remain firmly seated at full droop | Loose springs when lifted, bodywork constantly scraping on the ground |
| Front splitters & spoilers | Rounded edges (> 2.5 mm radius), ABE/TÜV approval (Maxton/Rieger) | Sharp metal/aluminium wings, loose parts, danger to pedestrians |
| Window tint (front) | At least 55% light transmission on windscreen and front doors | Light transmission < 50% (results on the spot in immediate seizure of the registration certificate) |
The police do not measure exhaust noise arbitrarily, but according to strict European measurement protocols (the static noise measurement):
The decibel meter is placed on a tripod at exactly 50 centimetres from the exhaust outlet, at an angle of 45 degrees relative to the exhaust flow, at least 20 cm above the road surface.
The engine is held at a specified rpm (usually 3.750 or 4.000 rpm, as stated on the registration certificate) and then abruptly released.
Does your registration, for example, state 82 dB(A) at 3.750 rpm? Then the meter may indicate a maximum of 84 dB(A). Does the exhaust exceed this level? Then you face a fine of several hundred euros and a WOK status.
Note for aftermarket valves: if a valve with a remote control can be opened manually without being linked to the official drive modes (such as ECE systems from Milltek or Remus), this is considered illegal manipulation.
Besides noise, wheel arches and sharp body parts are the most common reasons for confiscation of your registration:
If there is any doubt about wheel clearance, the police will drive your car diagonally with one front wheel and one rear wheel onto chocks or ramps. This causes the suspension to compress maximally on the diagonal (cross-axle loading).
Then the steering wheel must be turned from full left to full right. If the tyre at any point grazes or binds against the wheel arch lip, the shock absorber, or the inner liners, the vehicle is immediately rejected due to risk of a blowout.
Bodykits & Splitters: Parts from Maxton Design and Rieger Tuning are supplied with an official German ABE or TÜV homologation. These parts are tested for crash safety and have rounded edges. Home-made aluminium blades or sharp wings violate pedestrian safety and lead directly to seizure.
Don’t fancy fines, WOK reports or hassle with the RDW? In our professional workshop on the Riddererf in Nijkerk, our experienced technicians install sports suspensions, wheel sets, bodykits and exhaust systems daily, strictly within the legal framework of the Regeling Voertuigen and the German TÜV NORD guidelines. We check wheel arch clearance on the lift, re-measure track width, carry out razor-sharp computer-controlled 3D laser alignment and supply all required ABE and homologation documents.
Visit our workshop in Nijkerk for a professional fitment and noise check on the vehicle lift. Our technical specialists will thoroughly inspect your car and make sure you can drive with complete peace of mind.
We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".