|
WHEELS 'N CUSTOMS
SUSPENSION KNOWLEDGEBASE: KW HAS HEIGHT ADJUSTABLE SPRINGS VS. FIXED LOWERING SPRINGS
|
When you decide to lower your car for tighter wheel tuck and sharper handling, you face an important technical choice: do you opt for a set of traditional fixed lowering springs (such as from Eibach or H&R) or invest in KW HAS (Height Adjustable Springs / Height Adjustable Springs)?
This decision is particularly crucial for modern sports cars — such as the BMW M3/M4, Audi RS4/RS6, Mercedes-AMG C63 or Porsche 911. These cars leave the factory fitted with advanced, electronically controlled shock absorbers (such as BMW M Adaptive, Audi DRC / Magnetic Ride, Porsche PASM or AMG Ride Control). A full coilover kit often requires these expensive adaptive dampers to be removed and 'reprogrammed' with fault modules. With KW HAS you retain the active factory damping system 100%, while being able to adjust the ride height per axle to the millimetre. In our workshop in Nijkerk our technicians fit and corner-balance both systems daily. In this guide we break down the technology, fitment and adjustment options.
The principle of KW HAS is as well considered as it is effective: it combines the benefits of a coilover with the retention of your original dampers:
An anodised aluminium threaded perch with a continuously variable trapezoidal thread is fitted over the original strut top. Resting on this is the KW composite adjustment ring, which allows the lower spring seat to be turned continuously up or down.
The springs are made from chrome-silicon steel and are specifically calculated for the damping characteristics of the original shock absorbers. This prevents adaptive dampers from bottoming out or overheating due to incorrect spring rates.
Each KW HAS kit is supplied including matched elastomer bumpstops and dust covers. This ensures the piston rod remains within the factory valve’s safe working range at maximum compression.
| Feature / Function | KW HAS (Height Adjustable) | Fixed Lowering Springs (Eibach/H&R) | Full Coilover Kit (KW V3) |
|---|---|---|---|
| Ride Height Adjustment | Continuously adjustable (approx. 15 – 45 mm) | Fixed (not adjustable after installation) | Continuously adjustable (approx. 30 – 70 mm) |
| Preserve OEM Adaptive Dampers | 100% Preserved (no error messages) | 100% Preserved | Lost (requires KW DDC or ESC modules) |
| Solution for 'Drooping Rear' | Yes (level front/rear independently) | No (depends on fixed spring height) | Yes |
| Adjust Damping Force | Via original drive modes (Comfort/Sport) | Via original drive modes | Independently at the damper (Rebound/Bump) |
| Fine-tuning for Aftermarket Wheels | Perfect (set to the mm to prevent rubbing) | Limited (risk of rubbing with low ET) | Perfect |
| Price Level (Parts) | Mid-range (€ 650 – € 1.200) | Accessible (€ 250 – € 450) | High (€ 2.200 – € 3.800+) |
A common frustration for motorists who fit fixed lowering springs is the car’s appearance after installation:
The rear wheelarches of a car are often cut lower at the factory than the front wheelarches (to allow room for steering front wheels). When you apply a fixed lowering of, for example, 30 mm front and rear, the car can look noticeably lower at the rear than at the front.
This is called 'reverse rake' or a 'drooping rear'. With fixed springs you cannot correct this afterwards without removing the springs.
With a KW HAS system the technician adjusts the height of the front and rear axles independently on the lift. Is the rear 5 mm too low? Then we simply screw the rear perch up a fraction.
The result is a perfectly straight, aggressive and visually balanced wheelarch fill all around the wheels.
When you invest in an exclusive set of alloy wheels with a low ET value or a wide J-width (such as Concaver, Japan Racing or BBS), every millimetre of space in the wheelarch counts:
With fixed lowering springs it can happen that a wide wheel-tire combination just grazes the inner fender lip when the suspension compresses. You then have nothing left to adjust. With KW HAS we simply raise the car 3 or 4 millimetres, keeping the tyre free so the car runs 100% damage-free and curb-capable on the road.
Note: After any chassis adjustment, toe and camber change. A professional 3D laser alignment is mandatory to prevent uneven tyre wear and to centre the ADAS/steering angle sensors.
Fitting a KW HAS set requires specialist expertise and care, especially around the sensitive wiring of electronic dampers and hydraulic DRC lines. In our professional workshop at Riddererf in Nijkerk, our experienced fitters install KW coilovers and HAS suspension systems daily strictly following the official factory guidelines. We set the ride height to the millimetre to your specification and precisely align the wheel geometry on our computer-controlled 3D laser alignment bench.
Not sure whether your car is compatible with KW HAS, or would you like the perfect lowering to be measured and fitted immediately in our Nijkerk workshop? Our suspension specialists are happy to calculate it precisely for you.
We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".