Wheel Straightening: Radial Runout, Lateral Runout and Crack Repair Explained

Wheels 'N Customs Icon
WHEELS 'N CUSTOMS
SUSPENSION & WHEEL DIAGNOSIS: WHEEL STRAIGHTENING, VERTICAL RUNOUT & CRACK REPAIR

Vibrations after a Pothole or Kerb? Everything about Bent Wheels and Straightening

A heavy impact with a deep pothole in the tarmac, a nasty lip at roadworks or a slide against a high kerb: damage to the alloy can happen quickly. Many motorists notice it immediately as a persistent vibration in the steering wheel or seat at 80 to 130 km/h, or discover a slowly leaking tyre because the rim no longer seals airtight to the bead.

At the Wheels 'N Customs workshop in Nijkerk our specialists see wheels every day that have been 'treated' unseen by regular garages with stick-on weights in a futile attempt to hide the imbalance. However, a bent wheel can never be fixed with balancing weights; the physical deformation of the aluminium must be corrected with specialised hydraulic straightening equipment. In this guide we explain in detail the difference between vertical and lateral runout, how hydraulic hot and cold straightening works, and when a wheel is definitively beyond repair from a safety perspective.

1. The Two Major Deformations: Radial Runout vs. Lateral Runout

Not every bent wheel is the same. There are two fundamentally different types of geometric deviations:

Radial Runout (Vertical Deviation)

The rim is no longer perfectly round but becomes egg-shaped or has a depressed tread area. This occurs when the wheel hits an obstacle head-on (such as a kerb or manhole cover). The car literally bounces up and down, which is felt as a strong vertical vibration in the chassis.

Lateral Runout (Axial Deviation)

The rim edge swings from left to right relative to the hub flange. This usually happens with a sideways impact, such as sliding into a curb during a corner. The wheel wobbles, resulting in a violently shaking steering wheel that is noticeable even at lower speeds (50–80 km/u).

Combined Runout

In a heavy angled impact a combination often occurs: the rim edge is pressed inward and bent sideways. This requires a multi-stage straightening process in which both radial and axial runout are corrected with dial gauges.

2. Technical Comparison Matrix: Repair & Straightening Methods

Method / Damage Pattern Procedure & Temperature Suitable For Safety & Outcome
Hydraulic Cold Straightening Room temperature (no heat source) Light radial runout up to max. 1.0 – 1.5 mm Paint remains 100% intact; metal structure unchanged
Hydraulic Hot Straightening Controlled heating (150°C – 200°C) Deep dents, severe lateral runout up to 3.5 mm Prevents microcracks; local paint repair may be required
TIG Welding (Crack Repair) Milling a V-groove + TIG AC welding Single crack in the inner rim flange (barrel) Only safe if preceded by stress-relief straightening
CNC Turning (Diamond Cut) Digital probe + CNC diamond cutter Deep kerb damage on polished spoke fronts Restores factory-new condition with original gloss lines

3. The Professional Straightening Process: How Does Hydraulic Straightening Work?

Straightening an alloy wheel is precision work that requires the highest craftsmanship. A wheel must never be ‘cold-hammered’:

Phase 1: Clamping & Digital Runout Measurement

The tyre is removed and the bare rim is clamped onto the central spindle of the straightening bench using conical adapters. With an analogue or digital dial gauge (micrometer) the rim is slowly rotated.

This makes it exactly clear at which degree angle the dent is located and how many hundredths of a millimetre the deviation measures.

Phase 2: Hydraulic Pressure Cylinder & Heat Treatment

If necessary the deformed zone is heated with infrared or a controlled torch to approx. 180°C to reduce crystal stress. A hydraulic press cylinder with custom-shaped pressure pads gradually pushes the aluminium back.

The technician works in small steps and continuously re-measures until the runout deviation falls within the factory tolerance of less than 0.3 mm.

4. Safety First: When Is a Wheel Technically Total Loss?

Not every wheel can or should be repaired. The safety of you and your passengers is paramount at all times:

Strict Rejection Criteria according to TÜV & Manufacturer Standards

  • Crack in the spoke area or the rim centre: A crack in a spoke directly compromises the load-bearing structure. Welding on spokes is life-threatening and will inevitably lead to spontaneous spoke failure under heavy braking or cornering loads. Immediate rejection!
  • Misaligned hub flange: If the central wheel hub (the mounting surface with the bolt holes) is tilted relative to the wheel barrel, the rim can no longer be straightened without the bolt holes becoming out of alignment.
  • Deformations greater than 5 mm: With extreme dents the crystal structure of the cast aluminium is stretched so far that bending it back will inevitably cause metal fatigue and hidden cracks.
  • Multiple cracks on the same rim lip: If a rim is cracked in several places at once, the material has lost its overall resilience and the wheel is technically written off.

5. Vehicles with Increased Susceptibility to Bent Rims

Low-profile Tyres & Large Diameters (19" to 23"):
Very low tyre sidewall (series 30/35) transfers impacts directly to the aluminium rim<li>
Audi RS3, RS4, RS6 Avant (21"/22") • BMW M2, M3 G80, M4, M5 F90 (19"/20") • Mercedes-AMG C63, E63 S, A45 AMG • Volkswagen Golf R & GTI Clubsport on 19" Pretoria / Estoril • Porsche 911 (992) & Taycan • Cupra Formentor VZ5.
Heavy EVs & Commercial Vehicles (High Axle Load):
Huge vehicle weight forces a violent vertical impact over potholes
Tesla Model Y (21" Überturbine) • Tesla Model 3 Performance (20") • Audi Q8 e-tron • BMW i4 M50, iX • Volkswagen Transporter T6/T6.1 Bulli on 20" widesets • Ford Transit Custom • Mercedes-Benz V-Class & Vito.

Have Your Wheels Inspected & Aligned in Nijkerk

Have you hit a hard object, does your car vibrate at motorway speeds or are you unsure whether a rim can still be safely straightened? In our professional workshop at Riddererf in Nijkerk our experienced technicians remove your wheels and inspect the exact runout of the aluminium on the lift using micrometer dial gauges. We provide professional wheel inspections, precise balancing, damage-free tyre fitting and computer-controlled 3D laser alignment to prevent further damage to your suspension.

Do You Have a Bent Rim or Are You Troubled by Unexplained Vibrations?

Visit us for a professional wheel and runout diagnosis at our workshop in Nijkerk. Our wheel and suspension technicians will immediately assess whether safe truing is possible or if replacement is necessary.

 

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl