Lowering a Tesla Model 3 or Tesla Model Y is one of the most requested upgrades in our workshop in Nijkerk. Besides the obvious aesthetic benefits — a clean, sporty wheel fitment without excessive wheel gap — lowering yields a measurable reduction in aerodynamic drag (lower Cw value), which on the motorway translates into more favourable energy consumption and increased range.
At the same time, many Tesla owners understandably have doubts: "Will my valuable factory warranty on the drive unit and battery pack be voided? Will there be enough ground clearance for high traffic-calming measures? And how do you prevent irreparable damage to the jack points of the skateboard chassis?" As a recognised suspension specialist we explain in this guide exactly how European legislation, Tesla warranty conditions and workshop protocols fit together.
According to the European directive (Block Exemption Regulation) a car manufacturer may not simply void the factory warranty entirely when aftermarket components with TÜV approval are fitted:
The 8-year factory warranty (up to 160,000 or 192,000 km) on the high-voltage battery pack and the drive units (electromotors) remains 100% intact. Lowering springs or coilover kits in no way interfere with the high-voltage circuit or the battery management system (BMS).
If an original shock absorber or upper ball joint wears out prematurely, Tesla may reject a warranty claim on that specific part arguing that the altered ride height increased the mechanical leverage. Quality brands such as KW, Eibach and H&R offer their own product warranties for this.
Over-the-air (OTA) updates, Autopilot functionality, infotainment systems, paint warranty and corrosion protection remain fully covered under the official Tesla factory warranty.
| Chassis type | Lowering (Model 3 / Y) | Remaining Ground Clearance over Battery | Speed-bump Friendliness |
|---|---|---|---|
| Original Factory Suspension | 0 mm (Standard OEM) | M3: ~140 mm | MY: ~167 mm | 100% Standard (No restrictions) |
| Eibach Pro-Kit Springs | Front: 25 mm | Rear: 25-30 mm | M3: ~115 mm | MY: ~140 mm | Very good (Normal use of speed bumps) |
| H&R Sport Lowering Springs | Front: 30 mm | Rear: 30-35 mm | M3: ~110 mm | MY: ~135 mm | Good (Controlled speed over short bumps) |
| KW V3 Leveling (Comfort) | 0 to 20 mm adjustable | M3: 120-140 mm | MY: 147-167 mm | Excellent (Maximum battery protection) |
| KW V3 / ST XA Coilover Kit | 35 to 60 mm stepless adjustable | M3: ~80-105 mm | MY: ~105-130 mm | Attention required in parking garages |
The Tesla lithium-ion battery pack forms the entire floor between the front and rear axles. This brings specific technical considerations:
The aluminium belly pan protects the battery cells from stone chips and road spray. However, if a car makes 'bump contact' at high speed, a sharp kerb or point load can force a dent in the battery enclosure.
Note: Once the outer battery casing shows visible deformation, Tesla will refuse to repair the battery pack under warranty and the safety protocol requires a complete replacement of the battery pack.
Quality lowering springs from Eibach and H&R are wound progressively. This means the spring reacts softly in the initial range for ride comfort, but becomes exponentially stiffer as the suspension compresses further.
This effectively prevents bottoming out on high speed bumps and keeps the belly pan protected from harmful contact with the road surface at all times.
Lifting a Tesla requires a completely different approach than a conventional car with steel flanged jacking points:
Under the sills of the Model 3 and Model Y there are four round cut-outs in the reinforced chassis rail. Immediately next to these holes — less than 10 millimetres away — runs the edge of the high-voltage battery.
When a generic garage jacks the car up with a flat steel jack pad without an adapter, the metal slips off and presses the full weight of the car into the battery tray or the plastic battery sill. This causes cracks in the housing and can lead to short circuits or battery refusal.
In our workshop in Nijkerk we use only CNC-moulded rubber Jack Pads with a centring peg. The peg clicks into the chassis hole, so the weight is lifted 100% via the load-bearing structure and the battery pack remains completely free.
Lowering changes the geometric angles of the multilink suspension:
Don’t take risks with damaged jack points, cracked battery trays or unevenly worn tyres. In our professional workshop at Riddererf in Nijkerk our experienced technicians fit lowering springs, coilover kits and comfort suspension daily under Tesla Model 3 and Model Y. We work strictly according to the official lifting protocols, check brake lines and wheel arches, and perform a razor-sharp computer-controlled 3D laser alignment.
Not sure whether to choose progressive lowering springs or an adjustable coilover kit, or would you like to book a fitting appointment straight away at our workshop in Nijkerk? Our suspension specialists will be happy to calculate the exact figures for you.
We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".