Coilover Creaks When Steering: Causes, Thrust Bearings and Solutions

Wheels 'N Customs Icon
WHEELS 'N CUSTOMS
CHASSIS DIAGNOSIS: CREAKING & JUMPING SPRINGS IN COILOVERS

Clicking or Creaking When Turning In? Causes of Noises in Coilovers

You proudly had a quality coilover fitted for that perfect drop and sharp handling, but when parking, turning on the road or making a sharp low-speed turn you suddenly hear a worrying noise. This ranges from a dry creaking and grinding sound to a loud metallic 'boing' or 'ping' sound as if a guitar string snaps under tension.

In the workshop of Wheels 'N Customs in Nijkerk our chassis technicians see this complaint regularly after installations elsewhere. The assumption is often that the shock absorber is faulty, but in 95% of cases the cause lies in the spring dynamics around the thrust bearing (pilot bearing), missing spring preload or dirt built up between the coil spring and the aluminium/composite adjuster cup. In this technical guide we analyse the mechanical causes step-by-step and provide the definitive solutions to make your coilover steer quietly and smoothly again.

1. The Three Primary Causes of Steering Noises in Coilovers

In a MacPherson strut the complete strut assembly physically rotates when you turn the steering wheel. The following friction problems occur here:

1. Seized Thrust Bearing

The axial bearing (strut bearing) in the top mount allows the strut to rotate smoothly on its axis. If this bearing seizes due to dirt, rust or wear, the upper end of the spring cannot turn. The spring then twists until static friction is overcome and the spring suddenly releases with a bang (the 'spring binding' effect).

2. Too Little Preload

When a coilover is set extremely low without using a helper spring, the main spring can become unseated between the upper and lower spring perch when fully extended. During steering the spring shifts out of its concentric seat and lands crooked with a loud crack.

3. Dirt on the Adjuster Collar

Fine sand, road salt and brake dust collect between the lower coil of the spring and the anodised aluminium or composite adjuster ring. With every slight steering input the steel rubs over the grit on the adjuster collar, producing a dry, grinding and scraping creak.

2. Diagnostic Matrix: Symptom vs. Cause vs. Solution

Symptom / Noise Mechanical Cause Effective Solution
Metallic 'Boing' or 'Tring' when steering Spring suddenly releases; axial bearing seized Replace top mount + thrust bearing; fit torrington bearings
Grinding / scraping noise at low speed Sand and friction between spring and aluminium adjuster Clean spring seat; install plastic anti-friction ring
Crack when sharply parking + unevenness Missing spring preload; spring tilts in perch Fit helper spring or correct ride height
Knocking on short bumps (straight ahead) Drop link (anti-roll bar link) under tension Fit shorter/adjustable drop links

3. The Role of the Axial Bearing: Why New Top Mounts Are Mandatory

The top mount connects the shock absorber strut to the vehicle’s body tower. Inside this mount is an axial thrust bearing specifically designed to take rotational forces while the full axle load rests on it:

The Problem with Old Top Mounts

Many DIYers cut costs on a coilover kit by reusing the old factory top mounts. An OEM top mount is designed for soft, progressive OEM springs.

The much stiffer linear spring of a coilover exerts considerably higher point load on the ball bearing. A bearing already 60,000 km old will under this increased pressure immediately run stiff or seize, resulting in inevitable steering noises.

The Solution: Torrington Needle Bearings

For stubborn cases or motorsport topmounts (camber plates) our fitters install so‑called Torrington needle bearings directly under the upper or lower spring perch.

These wafer‑thin axial thrust bearings take the rotational force right at the coil. This allows the spring to rotate 100% friction‑free at all times, even at extreme steering angles and under maximum circuit load.

4. Spring Preload & The Importance of Helper Springs

A coilover must never be screwed down so low that the main spring becomes unseated from the perches:

MOT Requirement and Safety: The Loose Spring Test

At the MOT the car is lifted so the wheels hang freely in the air. The tester checks whether the springs can be moved up, down or sideways by hand. A loose spring leads to immediate MOT failure.

Quality brands such as KW Suspensions and ST Suspensions equip their coilover kits as standard with a flat secondary helper spring with a plastic intermediate seat. As soon as the car rebounds, this light spring presses the main spring firmly into the cup, permanently preventing rattling and misalignment noises.

5. Common Models Prone to Steering Noises

VAG Platforms (MQB & PQ35):
Prone to loose top mounts-axial bearings and tight strut towers
Volkswagen Golf 5, 6, 7 and 8 (GTI / R / GTD) • Audi A3, S3, RS3 (8P, 8V, 8Y) • Seat Leon Cupra (1P, 5F) • Skoda Octavia RS • Volkswagen Polo 6R / AW • Audi TT (8J, 8S).
BMW, Ford & Japanese Hot Hatches:
Anti-roll bar link tension and turret contamination from daily use
BMW 1 Series (F20, F21 M140i), 3 Series (E46, E90, F30) • BMW M2 (F87) • Ford Fiesta ST (Mk7, Mk8) • Ford Focus ST / RS Mk3 • Toyota GR Yaris • Hyundai i30 N Performance • Mini Cooper S / JCW (R56, F56).

Have Your Coilovers Professionally Fitted & Checked in Nijkerk

Do you want to be rid for good of creaking springs, knocking top mounts or fear of MOT rejection? In our professional workshop at Riddererf in Nijkerk our experienced technicians inspect and fit high-quality coilovers from KW, ST Suspensions, Bilstein and AP Sportfahrwerke daily, strictly according to the official German factory specifications. We replace worn top mounts, correctly adjust spring preload, lubricate with special dry PTFE coatings and carry out an ultra-precise computer-controlled 3D laser alignment.

Is Your Coilover Clicking or Do You Need Advice?

Drop by for a thorough suspension inspection on the ramp in our workshop in Nijkerk. Our suspension specialists will diagnose the issue on the spot and professionally resolve disturbing steering noises.

 

We use cookies to optimise your user experience, analyse web traffic and for marketing purposes. If you agree to our use of cookies, click "Allow cookies".

wheelsandcustoms.nl